after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
On opening a sample project located at https://www.nordicsemi.com/Products/Development-software/nRF5-SDK with keil V5 , I can directly have an error message “Cannot read RTE...
Hi there, I'd like to make some FIR or IIR filter on my nRF52840 DK. I guess I'm supposed to: 1) Provide .a file into SES project's tree (or as Additional Input File): 2)...
I am working on OTA update .
Right now i am working simple
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_doc_user_guide_modules_dfu_configuring_performing...
Hi,
Is there any command for reading the type of Nordic SoCs (e.g, nRF52833 or nRF52840) that is going to be programmed by nrfjprog/ J-Link Commander?
Thank you!
Hi Nordic,
I want to write a value from the application layer to the bootloader flash region through uart, and use this value to replace the button 4's function of entering...
Hi All,
I'm using buttonless DFU for upgrading the firmware and my requirement is I would like to know the time taken for complete DFU from my application.
One approach...
Hi, I am working on designing specifications for a new product, which will potentially be using the NRF9160 as the main processor, since the main application is centered around...
Dear Nordic support,
We are trying to know the current consumption during BLE RX & TX. However, there appears to be apparently conflicting information. Which is right...
Hi,
I want to use a single firmware to be flashed on two devices that can be used as a ble peripheral with DK Button 3 and as a central with DK Button 4 .
I chose ble_app_multirole_lesc...
Hi guys,
i am using nrf52840 controller.
and in that i have mbe at 0x0000000 location.
i have two bootloader stage. that boot1 and boot 2.
boot 1 i am using to validate...
I have gotten the FDS_ERR_NO_PAGES issue multiple times now. In our last pre-production run, it randomly happened to a few units (4 out of 60). For 3 of the units, the error...
Hello everybody, i succeeded to get the output from BME280 and MPU6060 sensors I need to merge them together
Kindly, I need help to Setup prj.conf file
Thanks & Regar...
