I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Hello everyone,
I want to be able to set a timer in my project. With this timer i want to be able to make my current comsumption evaluation easier.
I am using the nrf9160...
Cannot update modem (nrf9160) with "nrf connect 3.8.0"
Modem DFU failed with error: no matching trait found
no matching trait found
Installing older versions eg...
The datasheet tells me that the default source of the low frequency clock (LFCLK) is the 32.768 kHz RC oscillator (LFRC). so I took the crystal oscillator off my PCB, but...
After updating NRF Connect v3.9.0 to eliminate the recently documented JSON + connectivity errors with nrf Programmer and Power Profiler, my bash scripts utilizing nrfprog...
Hi，
1. Please provide me with an example of BMA280
2. The SDK: replication v1.7.1
3.IC:nRF9160
4. I tried to change the BME280 driver to BMA280 driver, but the following...
I am working on project in which i want to read data from sd card and send it to mobile through BLE , I am using ble_nus_send to send data but when i decrease the delay then...
Hello,
Using sd_ble_gap_adv_set_configure() with ble_gap_adv_params_t I observe that the actual time when the BLE_GAP_EVT_ADV_SET_TERMINATED event is raised is earlier to...
Hi All,
Likely because I am still quite new to this, but I have started with MQTT simple example and whenever I do use GuiConfig to make mods, it saves them to
proj/build...
The disccussion here
https://devzone.nordicsemi.com/f/nordic-q-a/24592/my-nrf52-nrf51-dk-kit-doesn-t-work
has been closed.
I followed step 4 and it took a few tries...
Hi,
I use a Segger JLink EDU (the big version, not the mini) to flash some custom boards. This used to work fine until I upgraded nRF Connect and got Programmer v2.0.
...
Dear sir/madame,
By an accident I selected Power Profiler Kit II when I wanted to download an application to “PCA10056 DK” . After that ‘download’ Power Profiler Kit II...
Hello,
I'm using NRF52832 as a controller for cellular modem and used the AWS IOT supplied with the NRF Connect SDK.
I want to use the AWS FOTA and I'm a bit lost, I added...
This builds on a previous Forum Post that was closed out.
There is a peculiar issue with the NRF52840 SAADC sampling. For an unknown reason, triggering the SAMPLE Task in...
I have a nRF5340 with a UART that connects to a circuit that is not powered on until it is needed by the application. So the UART must be powered off until the application...
