Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi,
I am searching for some methods to blocking the abnormal PCBAs which got short-circuit in DCC and DEC4 after SMT process. These abnormal PCBAs will cause BT pairing...
Hi
HI, I have developed an application for the nRF5232, using NCS 1.7.0. so i need to add the external flash.
I would need a working example running OTA with external...
The objective is to be able to send data back up to an MQTT server using the Nordic NRF9160 hardware. Nordic staff is helpful but only writes back usually in the very early...
I am using modem firmware v1.2.3 and NCS v1.6.0. Event GPS_EVT_SEARCH_TIMEOUT never occurs despite setting fix retry time to non-zero value. I am using GPS driver (no new...
Hi,
Can you please add your inputs regarding following 3 inputs.
1. Verification of Application after OTA upgrade before giving control to application.
2. Application...
I tried to get ADC values from my nrf52 based custom board on nrf connect app. I already made necessary changes in SAADC example program and able to get the voltage readings...
With rev 3 of the nRF52840 I am looking at upgrading the SDK from 16.0.0 to 17.1.0 on my current project.
I have product in the field based on SDK 16.0.0 with Soft Device...
1. Slave address is not reflected in the address register of TWI0.
2. other information is reflected in registers like operating frequency, SDA, SCL as well as enable. ...
Problem: While connecting with smartphone to several devices based on nrf52832, works only last connected device. Smartphone Application uses Nordic Android library (no.nordicsemi...
I'm using a TI Launchpad , together with the nRF Connect application on my Samsung Galaxy S21. I've got the launchpad connected to my computer and I'm using TI's bTool to...
Hi Nordic
After fellow your youtube tutorials, blinky sample can be built successfully. Flashing code to PCA10090 DK,
the LED started blinky well.
However, it failed...
I have a BLE application (Bluetooth peripheral app) using Zephyr with nRF Connect SDK v1.5.1 and Segger Embedded Studio. I was successful in adding/configuring the MCU Boot...
Hi All,
I'm getting this message everytime I open power profiler, previously working with PPK2, reloading doesn't resolve. Cancelling results in enumeration of PPK2 as unknown...
