Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I am working on nrf5340DK board and with sample example central_uart. I wan to find at what speed the application clock is configured and also want to change it...
There are lots of questions in the community related to use of multiple advertising sets. Common answer has been that it is "not support at the moment", see e.g.
https:...
I am using nRF52840-DK as a BLE sniffer. I have set up Wireshark to sniff the packets. Between c entral and Peripheral, there is an authenticated LE secure encrypted BLE connection...
Hi,
I'm working with a modified version of the secure bootloader included in the nRF5 SDK 17.0.0. I'm using an nRF52832 to update an STM32 over the air.
I have two update...
Hi all, I need to use the nRF5340's SPIM4 peripheral for 32 Mbps communication. I see dedicated device's pins are pre-assigned on nRF5340 for SPIM4, ad I want to use these...
We have an nRF52840 connected to a SAM4e over SPI. The nRF52840 is the slave and the SAM4e is the master. The 52840 uses a SPI slave routine based on the SDK17 SPIS example...
Hi there,
When parsing the GPS data from the Thingy91's GPGGA format, I've received invalid from such parsers.
Invalid:
I'm still able to successfully parse the value...
Hi,
We used modem fw 1.2.3 ncs 1.3.0 before and got upto 8 satellites when searching for a fix.
Using latest modem firmware 1.3.0 + ncs 1.5.1 we see no more than 3 satellites...
Hi,
I'm using the nrf52 mesh sdk v5 to make a provisioner based on the provisioner example of the mesh sdk.
During some provisioning, the provisioning process timeout...
Hi
in communication networks, GPS is often us to sync network elements and to get accurate timing.
with nRF9160 MFW 1.3, "GPS time based configurable IO-pin / pulse" is...
Hi!
I am developing an application that starts and stops gps occasionally. I am running the gps in GPS_NAV_MODE_PERIODIC with a timeout of 100s and an interval of 240s....
Hi,
We are having problems with nRF52840 dongle.
Intermittently pc-ble-driver-py throws the error in the subject when trying to open interface to nRF52840 dongle. After...
I got an average DRx power consumption of 415.03 µA for 2.56s in the Online Power Profiler for LTE. But unable to get the average power consumption of eDRx.
In the following...
Dear Community, I'm trying to use both datasheet-announced I2C interfaces, one as slave and one as master. Datasheet: www.mouser.de/.../BlueNor_BM833A_datasheets-1627946.pdf...
I have a BLE central application (a form of BLE to LTE bridge) which I have no choice but to redesign due to the dismal state of the supply chain. The original device which...
