Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hello
I'm having some issues setting up monitor mode debugging with the nrf connect sdk v1.4.99.
I've roughly followed the steps outlined in this guide , the exact steps...
Hello,
I am trying to program my NRF52840 chip with the Secure Bootloader UART project, in addition to the BLE App UART project as mentioned in the title. So far, having...
I am trying to work with Bme680 with I2C communication i can read every value but i cant read air quality value its always at 806516 value and does not change . I thing configirations...
I've been trying to integrate CLI over USB CDC ACM into my project, but I'm failing even to run the SDK example.
CLI works fine over UART, but it won't run over USB.
...
Hi,
My application has hard faults sometimes, and I'm trying to figure out the reason.
When it occurs - I have a hard fault log, but p_stack->pc is 0. I can't understand...
When I use j-link soft uart all good
but when i disconnect j-link the soft uart will error
like this so�rceid=2, status=0 sourceid=3, status=0 sourceid=4, status=0
Hello,
I'm new to BLE product and nRF52840 dongle and DK are my first BLE evaluation kits. I've some experience in Arduino AVR microcontroller. My setup is as follow:
...
Hi All,
I've been successfully using Martin's example - https://github.com/Martinsbl/nrf5-mpu-examples/tree/master/nrf52-mpu-easydma-using-gpiote-and-registers - for DMA...
I need to connect a PN532 V3 Module to a nRF52840 using SPI. I tested it using arduino IDE (I used those three libraries: Adafruit_PN532.h ( github.com/.../Adafruit_PN532...
We have custom board which is interfaced with PCA10040 board through bebug out port. Blinky example is working fine on 10040 but when I download it on evaluation board its...
Hi,
I've been following below tutorial and everything works fine.
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-characteristics...
The loader script provided to Segger for use with Embedded Studio includes
. = ASSERT (( __tdata_load_end__ <= __storage_flash_start__),
error: section .tdata overlaps...
Hi, I'm working on a project with the nRF52840 PCA10056 board. Using the IoT LwIP MQTT example, I can communicate with the insecure MQTT. However, I need to provide security...
I would like to use the GATT queue to discover ALL primary services. When using the SoftDevice calls directly, one would use sd_ble_gattc_primary_services_discover(conn_hdl...
