Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I have looked at forum_post_1 , forum_link_2 and forum_link_3 . In short, I am following instructions for my_dongle . I have ncs 2.6.1. I have clones of nordics git repos...
I notice in github.com/.../nrf802154_sniffer.py that there is a line saying: TODO: Add toolbar with channel selector . I know extcap supports these toolbar controls and a...
Hi
At nPM1300 product specification V1.1 page 148(8.1 Schematic)
The control I/F between nPM1300 and nRF5x is TWI(I2C), and there is four signals(SCL, SDA, Reset, INT...
Hi guys,
I've been working with the NRF52832 in the past days and I'm having issues with the GPIOTE interrupts.
It seems that there a latency of around 30us until the...
Hi! I created a unittest in my project using Zephyr CRC Unittest Example . It passes nicely using command line. However I cannot fix squiggles error in test code. I get following...
I am using NRF52833 Microcontroller to read data from the PCR based radar sensor. I am using NRF Connect SDK Version 2.6.1. I need help regarding reducing the power consumption...
Hello,
I'm new to the nRF5340 for BT/BLE; and was looking through older DevZone posts to see if I could find an answer to my question. Specifically, in RE: Query - Nordic...
When playing around with the nrf5340 Audio demo using nrf5340 Audio eval kits, if you play a tone through USB and transmit that through the Gateway to the Headset, you can...
Hi,
I am using the development kit nRF 52840DK running a firmware called pc-ble-driver . as USB-BLE dongle, together with the related python library.
I know that they...
The 52840 chip is stable with this and I have extended the code for my project, but I can't seem to get the 54L15 to be stable.
I will add the coredump and rebuild as well...
Hi,
I can't find any documentation for what the behavior is for the SPI API in Zephyr when the count of buffers in an spi_buf_set is > 1. In a transceive function, are they...
Hi! I have a problem with waking up from system on using gpio interrupts. Originally I was using SYSTEM OFF and that was working fine but i also wanted to wake the system...
Hello,
I know that this issue comes up from time to time. I'm raising it again, because to my opinion there have to be a solution for this. Perhaps there is, that's the...
I'm developing a FMDN locator tag and would like to use the locator tag sample in the connect SDK for testing.
Unfortunately, the requirements and exact procedure for running...
Hello,
* HW: nrf52840DK
* SDK: ncs v2.8.0
* APP: spi-master-slave example
In this example, I am interested in slave rx. Seeing this example, it apears slave makes...
