Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
In our NRF9160 application, we do not have a UART available and have to implement other means of logging crashes.
We have written our own k_sys_fatal_error_handler but it...
I am using a generic nRF52 dev board with the Arduino nRF52 core . I am trying to get a sample BLE service to display, but it cannot find it on my BLE scanner. After I couldn...
Hi,
I am trying to read read all nearby base stations' Cell ID, TAC, MNC, MCC.
Is this even possible to do with this DK?
At this point I have found these commands...
Hello,
I am trying the UDP sample for the nRF9160 DK board, using the iBasis SIM card that came with the kit.
The problem is that it does not register onto the network...
Hello,
I’m trying to interface the MAX32664GWEB+T sensor hub with the NRF52 by using I2C, I’m wondering if you could provide me any recommendation, libraries or codes for...
What I want to do is do UART communication (UART_1) between nRF52840 and nRF9160.
From the nRF52840 side, uart_poll_out is OK, From the nRF9160 side, uart_poll_out examined...
Hi Nordic team,
We have planned to use nRF5340 based BLE mesh device which is interface with sensor
We would like to transfer customized user data from one node to another...
I tried different nrfconnect examples and noticed that: C:/Nordic/v1.4.1/zephyr/samples/basic/blinky/build_nrf9160dk_nrf9160 blinky: rebuild solution + flash: OK also hello_world...
HI,
I am working NRF52810 with SDK 17.
I am able to pair my nordic device to mobile. but after pairing I want to send some data/receive some data.
how can I achieve...
In SDK 17.0.2, most places it looks like BLE_GAP_ROLE_CENTRAL is allowed to be undefined, except in nrf_ble_gatt.c line 142. Was there supposed to be "#ifdef BLE_GAP_ROLE_CENTRAL...
Hi Team, I am prototyping a product that includes DFU OTA using nRF52832. To get familiar with the topic, I am experimenting with the buttonless DFU example.
It is working...
Hi Nordic!
I am completely new to the Nordic MCU. Please, where can I find all the information (technical datasheet) about the NRF52840? What peripherals can I connect on...
Hello,
I want to use radio to send and receive data periodly. So I refer TimeSlot API in ' devzone.nordicsemi.com/.../setting-up-the-timeslot-api',and also refer the radio...
I am trying to implement the AWS FOTA sample from SDK V1.4.2.
I have already implemented the AWS IOT sample which works fine.
However, the AWS FOTA fails with mqtt_connect...
Hello there, I just try to demonstrate TCP examples in NRF5 SDK 15 and 16.
I got two linux boards, one of them Allwinner V3S with Debian Bullseye and the other one is...
