Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi, I have a BME280 sensor running normally with the nRF9160 on v1.2.0 firmware. When I updated the firmware to 1.3.1, I had to update the code to run I updated the files...
Hi, I have a simple voltage divider circuit and I am measuring analog input from in between the resistors. I am using a custom NRF52832 being powered by a DK. I get quite...
I recently purchased a Thingy91 and have been following the start up guide but have been running into an issue with the thingy91 being recognized over USB. I was able to connect...
Hi Nordic,
I am developing a distance measurement application between the nrf52840 and nrf52833 unit for the long distance mode.
for the nrf52840 as center which running...
HI
I'm using SPI connecting to mutiple max31856(two now) on nrf52DK and SDK15.3
so I control my ss pin to pull low by myself
chip select by changing spi_pin like some...
a data array, length is 2048,use function "sd_ble_gattc_write", a error occurred, length less than 240, no error.
do {。。 err_code = write_configure(m_center_handle,14...
Hi all,
I'm using NRF SDK v17.0.2 and IEEE 802.15.4 stack library. I want to implement sleeping device. I think I should use sys_sleep_request_ms function to make the device...
Hello, Is it possible to use the USB Pins for Uart? no USB Protrocoll Would be nice if i can use the USB socket for UART with my other projects so i dont have to create a...
Hi,
There are new softdevices (v7.0.1) out for the nrf52832 and nrf52840 but, I don't see any mention of them on Nordic's infocentre. Are they compatible with SDK 16.0...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hi,
I have been working on DFU ble update with nrf52840 DK.
Using the onboard buttons I'm able to go to DFU mode where as for our custom board there's no buttons and I...
I am developing a firmware for the nRF52805 SoC with a nRF52 DK. I want to implement the DFU support on the same. The secure bootloader example in examples\dfu\secure_bootloader...
Hi everybody,
I'm trying to update a device (a PineTime device with a nrf52832). The firmware is using legacy DFU. I already have a DFU package, so, I only need to perform...
