Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
If you call nrf_serial_write() once to transmit some data, and before the data from this first call is transmitted, you call nrf_serial_write() again, will the NRF_SERIAL_EVENT_TX_DONE...
Hi Team
I would like to know are there any pic libraries for nrf24l01?
Need to send and receive data from PIC16F1526 to an other PIC MUC via nrf24l01 transceivers.
...
Hi,
My task is to work on NFC , I know the basic working principle of NFC . Here I have seen the nfc uart example .
I would like to transmit the device name, mac address...
Need advice on choice of advertisement flags.
Beacon advertises alert and non alert beacons: On the alert beacons the central is required to connect and respond to the beaconing...
I have looked at and used the following references:
https://devzone.nordicsemi.com/f/nordic-q-a/47484/ble_gap_evt_scan_req_report-not-working
https://devzone.nordicsemi...
Is it possible to implement open thread cli using 16 castellated pins of BT840 ?? I can change the uart pin by rebuilding the open thread libraries ,
Can I avoid using...
Dear all,
In our project we are using "nrf52840" IC is used. We need to check its strength in various physical layer by loading the " Direct mode code ".
We have sucessfully...
Hi !
I need to develop a BLE communication link between a smartphone (Android first, iOS after) and the BL654 Laird platform (based on nRF52840).
I found multiples strategies...
i am developing a bike power meter and designed my own hardware.
From software point of view I used the Ant+ bikepowermeter example from Nordic.
So far my status is, ...
To the kind attention of Nordic support team,
Could you please help me finding documentation about the subject I mentioned?
Let's suppose we have got a peripheral and...
Hello,
I am working on ble_app_uart example on nRF52840DK.
I am using one switch (gpio) for advertising_switch() function. It means on changing the position of the switch...
Hi,
Would you please tell me how can I dump a memory and save into a file in keil uVersion 5.24?
For example: I want to read the flash memory 0x00000000 to 0x00010000...
There is an option to 'Clone device's services':
A message pops up briefly to say that it's done it:
But it doesn't say where it's put it, and I can't see any...
Dear all,
I have picked the Ruuvi project : https://github.com/ruuvi/ruuvi.firmware.c and change the configuration to adapt with nordic dongle.
But after flashing, my...
