Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi Nordic ,
I am working a project on nRF52830 with SDK 15.3. Now, I developmet on a central device, I need to connect with peropheral with more than one service , how...
Hi.
I'm using nRF52840 Developement Kit and my environment are below.
OS : windows 10
SDK version : 16.0.0
Tool : nRF Connect (with DTM,Programmer app) / Seger embedded...
Hello everybody,
I'm trying to flash an example code (let's say the blinky one) from the SDK (15.3) onto the Arduino Nano 33 BLE board.
I know that is possible to flash...
Hello,
I'm trying to resolve an issue in my project.
It appears there is a memory leak.
In logs I can find the error code : 0xBFED
Do you know what that code is? ...
Hi,
I recently had a problem about timestamp that it's all 0 on the RTT Viewer.
And i 'm based on the nRF5_SDK_15.2.0\examples\peripheral\rtc to check the timesteamp....
Hi Nordic
I have some issue When using NRF52832 central to connect the NRF52832 peripheral.
i am following the SDK15.3.0 ble_app_uart & ble_app_uart_c to deign the central...
Hi
I have a question about LXFO input on external low swing clock setting using nRF52832.
I can see the input specification of external low swing clock about only peak...
Hi,
I am currently developing a stationary BLE device. I am testing the nRF52840-dongle in combination with the pc-ble-driver. For that purpose, I am using the connectivity_4...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I am operating in a "peripheral" configuration, with bonding enabled. "BLE_GATTS_EVT_WRITE" occurs when notification is permitted...
We're porting over some software to the Arduino Nano 33 BLE Sense. This board comes with an nRF52840 clocked at a max. of 64MHz. However, the same code runs about 2x slower...
I want to send Tx power in advertisement packet.
Currently I am using following code.
int8_t txpower_level;
static ble_advertising_init_t init =
{
....
Customers use nrf52810 flash program to store data, but want to know what flash start and end address can be written, please point out that you can refer to that document...
Dear Nordic Semiconductor
I am using device:
NRF51802 bluetooth 4.0
Product Introduction:
Features:
1.Adopt NRF51802 bluetooth 4.0 BLE SOC
2.ARM CORTEX-M0
3...
Hi , I use the pc-ble-driver to developer desktop tools, like nRF Connect. Unfortunately, I don't know Java. I‘ve tried to used examples that work(heart_rate_collector and...
