Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
I am use bonding and want to forbid new bonding if proprietary authentication criteria is not met.
For example, I want to allow bonding only if my device is on...
Hi, I am using nRF5_SDK_15.0.0_a53641a.
I'm using code below to start WD and I'm not feeding WD.
After WD reset, I'm looking at RESETREAS register and DOG bit is...
Hi,
we are currently in the process of optimizing our connections for better throughput. Use-case is connection based FruityMesh ( https://github.com/mwaylabs/fruitymesh...
Sir i am using only one nrf52840 board
Sir i am changing router role to coordinator role and also remove the zb_ed_role in preprocessor definition
now the project building...
-> The Command zdo match_desc 0xfffd 0xfffd 0xc05e 1 0 0 is Entered in the teraterm this function taking the input from those command by using argc and argv
-> our plan...
Hi,
I have some question, If I use BLE protocol.
From nRF52811 Product Spcification as link https://infocenter.nordicsemi.com/index.jsp?topic=%2Fps_nrf52811%2Fkeyfeatures_html5...
I would like to set the tx power for all roles such that the nRF52840 (s140) never transmits anything above my specified level. This includes advertisements, past connections...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hi,
I think you have deadlock situation or wrongly used interface in driver at_cmd.
The master branch is using functionality using function at_cmd_set_notification_handler...
Versions:
Segger Embedded Studio v418,
nRF SDK v1.0.0 tag
For the NB-IoT network I wish to connect to, I need to specify the APN, I can see through "Configure nRF Connect...
nRF52832 doesn't seem to wake up when an event is generated. I confirmed that the RTC0 is active and the event is generated
upon COMPARE[0] match using the SES debugger...
Since GPS can only function during the PSM window and the network can ignore the nRF9160's request for PSM mode, I need a solution that works with and without PSM mode. This...
Hello,
I need help. I cannot see my earlier ongoing ticket!? I have been working With it for the last couple of Days and today i was asked to share my Project but now the...
Hi,
I have a question for production firmware update using JTAG/SWD for nRF9160 modem:
The Segger generates merged/hex. So the merged hex includes the modem code updated...
