Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I am trying to open example project(nrf9160, assent tracker project) with SES V4.20a(download form nrfconnectSDK instruction)
1. It doesn't recognized header files.
2...
hi all ,
now , i need get gps latitude and longitude information.
reference nrf9160_gps.c file,it should be do it now ,
how to use driver to get PVT? ,
follow , it...
Hello ,
I use SDK 15.3 , chip is 52811
I refer to the example of 52840 "examples \ peripheral \ timer"
The following is the example code, I have not changed it.
...
Hi, I am trying to debug firmware on the nRF PCA10059 usb dongle board, through a nRF10056 dev kit by attaching a standard 10 pin header on the usb dongle at P1 & connecting...
Hi everyone
Program crashes after few minutes while trying to run two threads(GPS thread and a thread used for caculating the battery voltage) simultaneously.
Please...
Hi,
I am trying to understand how the connection parameters and settings work and how they change the throughput. For this sake, I have been experimenting with the ble_app_att_mtu_throughput...
Hi everyone,
I few days I tried run on my NRF9160 DK CC310 hardware RSA crypto functions.
When I started it at first I ran security_service demo where board run random...
Hi,
When I write a very simple USB audio device that just pass a sinuous wave created in a timer that runs at a 16KHz freq - how can I tell "someone" on the host listens...
Hi,
I'm wondering if there are any samples that show how to use sleep mode on the nRF9160. Not quite sure where to start to look for resources on this. Any documentation...
Hello,
Please check this code for BLE disconnection.When peripheral tries to disconnect from the central , it is disconnect successfully the first time but second time it...
Dear Sir or Madam,
We are currently trying to connect two nRF91 to the NRF Cloud service. We were able to activate the SIM card connected to the board, however, we were...
Hello,
I was having a lot of trouble with BLE_GATTC_EVT_TIMEOUT on the nRF51 and softdevice v2. But now I continue to have the same problems on an nRF52 with Softdevice...
Hello. Want a bit clarify some ESB protocol features on nrf52. As I understand 8 separate pipes allowed to use. So I can send separate payloads via every pipe. Here is some...
Hello,
I would like to use the serial port library with free RTOS. I read several threads that timeouts do not work when using free RTOS. So I tried to use the lib without...
