Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hardware: nRF52832
SDK 14.2
Segger Studio
Hello Sir or Madam,
We've made a new hardware variant of a previous design with an nRF52832 on much smaller form factor...
I use the QSPI(SDK15.2) of NRF52840 to read and write FLASH. Every time I open QSPI function, QSPI is closed after writing flash, but after close QSPI, there will be occasional...
Hi,
I want to capture data from TWI ADXL345 and send them by ble_nus_data_send() to mobile. Timing of data sending is done by application timer. My problem is that when...
Hi,
I tried to merge ble_app_multilink_central and ble_app_uart_c.
But, when I run the project It errors like below
I thougt the problem is the address of RAM_START...
HI,
my new BLE project is using nRF52810 chipset. Following is the requirements:
1. BLE nRF52810 will pair with iphone/android taplet
2. iphone/android table will...
Hello All,
I am using "nRF52840-DK" with "nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71" SDK which i am using with SEGGER Embedded Studio(SES) .
I tested the "Blinky"...
Hi, weird issue. I am using the nRF toolbox to connect the nRF52832 (configured for HRM) for use on android. The thing is, on my personal phone ( Samsung galaxy s10+) everything...
Hello.
I have several problems with building this demo: https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo As author recommends:
Download and extract...
Hi,
I would like to increase the length of read & write characteristic value to 29 bytes. I changed the NRF_SDH_BLE_GAP_DATA_LENGTH = 36 & NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hi,
I try to build a simple BLE central device from nRF52840 dongle.
Using Nordic's nrf Connect desktop application I upload connectivity FW.
I want to replace nrf...
Hello,
To the nordic experts, please share your opinion or any suggestions are welcome in finding the feasibility of nRF52832 SOC in our product based on the information...
If I go into a power save management, can still set any digital GPIO as an output without consuming current.
Push-pull?
For example I connect the GPIO to the Gate-Mosfet...
