Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello all,
I recently migrated from SDK 15.0.0 to SDK 15.3.0 and as a result tried to migrate from SD 6.0.0 to 6.1.1.
My application goes to sleep after a while and when...
I am new to this environment.
Attempting to create a simple BLE app similar to the built-in BLE, but with some buttons to send predetermined commands to devices. Using the...
I applied Bonding to the UART example(ble_app_uart).
Bonding combined with the UART example works well, but there is one problem.
1. I did Bonding first. 2. After that...
Basically I get an Attribute not found error from sd_ble_gatts_value_get() in the nus_ble.c and then I never get any NUS events in the application. I'm trying to figure out...
Hi!
We have working solution with custom rf protocol based on NRF52832 and NRF52840(now it use 2 Mbps Nordic proprietary mode). Now we want improve it.
Could You give...
HI,
I have found some problem with nrfutil (version 5.2.0 installed from pypi).
Problem description:
When I am updating dfu with success (correct keys, packages etc...
Greetings,
I'm using 3 NRF52832 boards, s132 and SDK 14.2.0. I'm interested in connecting two hrs peripherals to a single hrs central, but have found some posts that say...
When creating an attribute specifying vloc as BLE_GATTS_VLOC_USER, it is not very clear that a storage pointer must be provided on creation of the attribute and cannot be...
Hi,e verybod, I use nrf51822 to do bluetooth keyboard, I hope the function is: After bluetooth keyboard connect the host,how to determine whether the connection is window...
I'm trying to create a virtual beacon on an Android Phone using nRF connect V4.22.3. Android Version on the phone is 8.1.0.
I've enabled a beacon using Advertiser. However...
In an BLE example I have a characteristic with the value 0x00001234. In the nRF Connect 2.0 for iOS i see the value 0x00001234 and in nRF Connect for Desktop v3.1 i see "34...
Using the logging module in ncs v1.0.0, I see some extra characters after the timestamp " <0x1b>[0m<inf>" and at the end of the line ", is there a way to fix this?
The terminal...
Dear All,
I am fairly new to the nrf9160 and the Zephyr Os.
I am trying to write a simple example code for watchdog. All I want to do is to reset my board if I don...
Hi,
I have some nRF52840 DK boards and want to develop a system with 5.0 BLE.
But my linux box host has older version:
Bluetooth: Core ver 2.22
My first question is...
