Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Goodday
I have integrated the fstorage peripheral example with the BLE_beaconing example. SDK 15.2. I can read and write strings. I cannot read back the hex number if...
Hello,
I am using nRF52832 devices and calculating the distance using RSSI, but it is not that accurate.
Can you please let me know whether we can calculate the accurate...
Hi @ all,
I am trying to get the serial DFU process runnning. The process worked fine for nrf52832 and now I am on the nrf52840.
I encountered a problem with executing...
Dear all,
I'm new to Ozone and hope that you will forgive the simplicity of my question.
I'm trying to acquire a simple trace (Code Profile) of the blinky example with...
Hi
I am new to all nordic BLE modules, currently working on nrf52832 eval board. I am trying to scan the BLE Beacons "EDDYSTONE" and their RSSI level for my tracking application...
Dear Nordic
I edit the uuid from sd_ble_uuid_vs_add(&nus_base_uuid, &p_nus->uuid_type), all can success but only one uuid start with 0xFB, when use 0xfb, nrf_app_uart fail...
Hello
I am using SDK 15.3 ble_uart_central and peripheral example.
I am trying to transmit an array of integers from peripheral node to central node. Please help me with...
I need to run gc because I get rc =FDS_ERR_NO_SPACE_IN_FLASH.
So I run gc simple as written in https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.3.0...
Hi all
we used a nrf52832 to communicate over SPI and I2C at the same time with some sensors. This works fine.
At the moment I try to convert the project to nrf52810 but...
Hello,
does anybody now when the sniffer will support coded PHY?
I found a similar questions but no answer yet...
https://devzone.nordicsemi.com/f/nordic-q-a/42216/does...
Hi,
I would like to combine NFC - BLE pairing and launch app record. Naively I thought I would write the second data right after the first:
But this does not work. Reader...
I am using an NRF52832 on an energy harvesting board where lowest power is critical. I can achieve ~2 uA current consumption in idle state (waiting on RTC interrupt), wake...
Hi,
I work on the nRF52840 DK with the ble_app_uart example and I want to add a timer using app_timer api,
in order to create RTC time/date timestamps for my sensors raw...
Hello
I am using SDK15.3 and nrf52832 development board.
In my setup,
1. I have a few peripheral nodes whose only job is to transmit some arbitrary packets ( say P)...
My setup consists of a Raspberry pi and a PCA10056 dev-board (NRF52840). I followed the instruction from here in order to set up the Raspberry pi as boarder router and connect...
