Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello there,
I am working on a project in which two devices(one is central and other is peripheral ) uses Nordic bluetooth controller for connection and data exchange. nrf51822...
Hi Nordic,
I plan to use the newest SDK (because the ATT MTU > 23 is need) for NRF52832 to develop a PC tool to connect with Nordic BLE peripheral devices, and then send...
Hi, i am using SDK15.0.0 with nrf52840 chip.
I am interfacing a SPI device in the SPIM0. The SPIM module looks working fine without a softdevice.
But when i integrate...
SDK - 15.0.0
IDE - Segger Embedded Studio
Computer Platform - Windows 7 - 64 Bit
Hi,
I am using an android phone to write a 32 byte array to the nrf52 device which...
nRF51_SDK_10.0.0\examples\ant\ant_plus\ant_bsc\bsc_tx\combined\button\pca10028
ANT BSC Speed event time not change After a period of work although button press or relea...
Hi. I am a beginner with nrf52832. Trying to get Bluetooth and UART and a I2C peripheral working at the same time. I had a working version of the I2C peripheral and UART working...
I have problem with both custom boards and DEV board.
From a certain time after GPIO direction bit seems not effecting the pins.
To get rid of software factor, I all erase...
Hello,
I'm currently using nrf8001 to sent a 20-byte packet. It works fine and my phone application receives the right data. However, when I send another packet that has...
Hi,
I try to create program which will save same data on SD card, I'm using evaluation board nrf52 (nrf52832) and using SDK 13 (nRF5_SDK_13.0.0_04a0bfd) and programing it...
nRF52832 custom board plus some devices. Using SDK 15
I want to count pulses from a previously configured accelerometer. Pulses are slow, around 500 per minute.
I have...
I am experienced with ARM Cortex-M devices, but new to Nordic. I am using C++, and have a publisher-subcriber event driven framework of my own in place already. My own software...
Hello
I am experimenting a little with the Nordic Thread SDK v2.0.
I have a usecase that requires coap security. I havent been able to find info on secure coap connections...
i just got my nRF52DK, turned it on, and tried to read the nfc tag with my phone, but it looks like it is a broken link:
https://www.nordicsemi.com/start52dk
Perhaps...
Hello community,
I'm facing a problem with nRF51 DK PCA10028 and a function call on connected or disconnected state including NRF_LOG commands. Using SDK 12.3.0
On connected...
Hi, i have an existing product but the firmware has been removed from it. i have tried to use the dfu to replace the firmware but i dont know how to get the chip to the point...
