Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hello,
I use an nRF52840 that I program with Segger Embedded Studio. I am using J-Link driver version 6.44f.
When I want to connect to J-Link I get the following message...
Hi, all! After updating all libs can't flash. Have this error: Tested also with asset_tracker sample. Using runner: nrfjprog nrfjprog --ids Flashing file: /home/ilya/projects...
Hello Dear support,
Please help me with the error. I understand from the documentation that 0x11 err_code for nrf_drv_twi_tx() means invalid data. But I dont understand...
Development software:
1. SDK 12.3.0
2. 51822 module
3. GCC
Computer platform：
1. OSX
Hardware version:
51822AA
Description：
I used the original hex in the...
Hi,
we are developing on the nrf52840 using SES and SDK 15.0. This is a custom board. Softdevice is s140_nrf52_6.0.0_softdevice.hex
We are sampling distance with vl53l0x...
Hello,
I use the SDK15.3.0.
(nRF5_SDK_15.3.0_59ac345 -> example -> ble_peripheral -> ble_app_uart ->pca10040 -> s132 -> ses)
The default baudrate of uart is 115200bps...
I used SEGGER Embedded Studio ARM 4.16 to by mistake program a NRF52-DK PCA10040 with a PCA10056 example from your SDK collection. As a result, I now persistently get "Failed...
Hi,
I'm developing multiprotocol applications based on examples from Thread SDK: Proximity/CoAP server and BLE UART/CoAP client. All CoAP communication in this examples...
SDK version: 15.3
Soft-device version: 6.1.1
Hi,
I've been working on a low power application where every 10's of uA is important. My application requires SPI as...
Can you provide documentation of the energy costs for creating/verifying ed25519 and NIST P-256 signatures with the CryptoCell CC310 peripheral found on the nRF52840 device...
I am trying to set pins when I press a button, and clear is as soon as I stop pressing the button, however the board turns on all leds at once and does not respond to input...
I came across this old thread, which asks the same question, but was abandoned by the OP ( ) without follow-up:
https://devzone.nordicsemi.com/f/nordic-q-a/26699/52832-saadc...
Hello,
I am looking into migrating DFU and Bootloader over BLE from SDK v15.0 to SDK v15.3. I have a few questions about the code changes which I was hoping I could get...
I was reading about Mesh DFU and noticed that when it happens, the receiving node will rebroadcast it to all devices within radio range. It seems like devices will pick up...
Hello all,
I am trying to adjust the current consumption of my device based on nrf51822 s130.
A have read the https://developer.apple.com/hardwaredrivers/BluetoothDesignGuidelines...
