Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi,
I have tried the following example: infocenter.nordicsemi.com/index.jsp
Everything works fine (I can generate a notification via a calendar event and see it via the...
I get NRF_ERROR_INVALID_PARAM when calling sd_ble_gatts_characteristic_add(); If I comment custom service initialization where is this function I get the same error NRF_ERROR_INVALID_PARAM...
Hi, For a new project we need a smaller devices compared to to the nRF52832 dev board but still want to stay with the nRF52832 chip without making our own PCB. As an alternative...
We have a large number of units in the field running on SDK 13.0.0/S132 SD 4.0.3 and in order to add new functionality we need to migrate to SDK 14.2.0/S132 SD 5.0.0 via DFU...
Hi,
This is a follow up of issue: https://devzone.nordicsemi.com/f/nordic-q-a/28211/thread-dfu-upgrade-problems/111436
We're trying to perform DFU by following "Thread...
nRF52810 only supports S112 so the max throughtput anyone can achieve is 330 kbps .. please provide proof.. test data. Only nordic employee please answer this or someone who...
In SDK 15 the bootloader DFU enter check in nrf_bootloader.c has the following code:
if (NRF_BL_DFU_ENTER_METHOD_GPREGRET && (nrf_power_gpregret_get() & BOOTLOADER_DFU_START...
Hello,
We are working with Low Energy sensors that are programmed to make a periodic ADVs to our scanners/apps/Raspberries, in order to start a service if required. So the...
Hi,
I am using cli and made my own command like bellow, as you see i have a command with 3 sub commands. But i think my idea is primitive because if i have 1000 sub command...
I am starting building industrial-grade system which contains several nodes connected via wireless channel.
As a wireless protocol I decided to use BLE 5 due to long ranges...
I am trying to program mpu_simple https://github.com/Martinsbl/nrf5-mpu-examples with Segger, and I get to connect sensor MPU6050 to my board but I do not receive datas of...
Hello. I followed all the steps provided in the readme document. After dragging and dropping the hex file to the j link, the led 1 starts to blink, indicating that the board...
With an nRF52, is it possible to wait longer to measure the RSSI on a channel? I'd like to measure the RSSI over 1msec or so, rather than a tiny 8us (typical) snapshot.
Hi,
This is my first time to use Nordic product and I have used nRF52832 based SDK 12.0 and SoftDevice132 v2.0 about 2 months. And the IDE used for devlopment is KEIL MDK...
