after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I'm using nRF SDK v15.0.0. I have have added battery service using this online tutorial: https://www.novelbits.io/smart-ble-lightbulb-application-nrf52/ . The code...
I try to eddystone url beacon with advertise every 5 second. I changed
#define APP_CFG_NON_CONN_ADV_INTERVAL_MS 5000
upload code in nrf52832 module I used NRF connect...
Dear Sir,
I am working with SDK15, nrf52832 and softdevice s 132.
I am using ble_app_template with slight modifications.
Now it will advertise for a duration of 10...
Hi
I am using nrf sdk 15.2.0 for MEsh networking.(Mesh SDK version 3.3).
Hardware platform -nrf52832(pca10040).
Steps followed:
1. Compile and Run light switch demo...
Dear nordic,
I want to test Thread. I selected Thread Cli example for this. but i need to know something regard this. Iam new in the thread. from this example command is...
Hi, I am trying uart example now, not first time. I made it and check the receiving and transmitting data through ble last week.
The problem is it is not working now. Building...
When i am sending data packet from node a to node b why is b node relaying the message back and forth.It shudnt do that .
I just have 2 nodes in the current setup. Node...
I watched https://devzone.nordicsemi.com/f/nordic-q-a/33591/softdevice-s140-v6-0-0-how-to-set-the-channel-mask-for-different-channels
Does this work the same way in my situation...
I'm having a heck of a time getting the SAADC to just return one sample in a blocking manner using SDK 15.2.0
I'm pretty far along in developing a couple of nRF52840-based...
How many capture compares does each timer have on the nRF52810?
The documentation is conflicting. In the "Registers" section for the Timer peripheral in the data sheet it...
Some comparison charts I've seen from Nordic indicate that the standard is supported by nRF52840 only, but it is not clear if it can actually do it in the three bands specified...
Hello,
I have a peripheral based on SDK 9.0. I have tried to follow the peripheral proximity example to get bonding working with the app. The App is currently running in...
Hello,
Im new to the Nordic Ecosystem, and have been trying to set hardware uart with Nordic Thingy 52 with CP210x using the sdk13 uart example. I included the uart driver...
