Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
hi,could i ask you what should i do in order to use ant on the pca10056 board? i added the s340 softdevice but no example works on the board. thanks a lot!!
I am working on a MQTT related application on nRF9160 DK, and grabbed mqtt_simple as a baseline for development. All of my libraries are back at the last tagged releases:...
Hi, I'm confused, according to Bluetooth 4.0 Specification bytes are send in Little Endian byte order, and with LSB first in every byte. So when I receive raw data from characteristic...
When running "pip install nrfutil" I get this message - "Could not find a version that satisfies the requirement antlib~=1.0b (from nrfutil) (from versions: ) No matching...
Hi all,
In Nordic SDK ble_app_gls Example , the following UUID is added as part of Advertisement packet
static ble_uuid_t m_adv_uuids[] = /**< Universally unique service...
Hello,
I'm currently building a project for the nRF52 (using SDK 15.2). I need to have 2 ADC channels, 1 for temperature sensor and 1 for battery level. I figured that I...
I want to let nRF9160 communicate through UART with 3.3V logic level, but the logic level is originally 1.8V.
I have been reading nRF91_DK_User_Guide_v07.pdf, but I'm not...
Hello,
I'm working on the implementation of some custom services and I started to question why the SDK implements the service modules as instance managers (as of SDK 15...
We are having an issue with pc-ble-driver ( https://github.com/NordicSemiconductor/pc-ble-driver ). We're using the nRF52840 dongle. We have compiled and run the `heart_rate_monitor_v6...
Hi,
I want to communicate with a legacy device nrf24l01p+ based using a nrf52840 DK.
Firmware of legacy device setup the card in this way:
I take the esb_ptx esample...
Hi
Getting problem in DFU feature while using segger embedded studio.Device gets programmed successfully but stops working after that.
I am following the same process...
I am looking to check signal strength and would like to be able to do it as easily as possible.
The default asset_tracker sends messages which can be seen in the nrfcloud...
We have an application running on our devices that are using ble_nus to communicate with a base station.
The use case is approximately something like this:
On button presses...
Step1 : init a Client model in Provisoner:
Step2 :config this client:
Step3:set the pub address of this client & control the remote gen_onoff_Server model: but it...
Hi
I've found an issue with the serialization code for the function sd_ble_gap_device_name_get in the SDK 14.1.0. As far as I see the issue still exists in the SDK15.0.0...
