after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi, I want to start some projekt with BT840 module and use Keil to programming it. Also, I have Segger jlink programmer but I don't know how start. Can you give me some tips...
Hello,
we are using nRF52840 and have to directly use the CRYS API of the CryptoCell310.
In the documentation of the function CRYS_HASH_Update, the following is written...
When I use the battery to power on, I get NRF_POWER-> RESETREAS = 0x00010000. I check the register manual to see that it is GPIO wake-up. But I didn't configure GPIO wake...
Hello,
I am using Samsung Galaxy Tab A (2016) with android version 5.1.1 build LMY47V and I can not connect to the bluetooth module at all. In the log of the nrf Connect...
For an ADV_IND advertising event without any Scan Requests, what is the maximum amount of time that the radio's receiver will stay on?
Is this parameter configurable?
...
I am trying to configure SPI with BLE using softdevice S130. But SPI is not working properly when I used it with BLE, although it is working fine without BLE
Hello Nordic,
I am having problems getting the PPK to work with my nrf520840-DK application. I am happy to share my code with you, but first a hardware setup-description...
Hi,
Do you have an example in how to upgrade the firmware of the NRF52 family through UART via IAP? I am keen to update the FW of my product without the necessity of using...
Hi,
I'm developing a central application and I would like to be able to get the full device names of the peripherals I connect to. I know how to get the device name from...
Hello,
I'm using the nRF9160 DK for a datalogger with LTE capability, and I'm using the Arduino shield "Mux Shield II" which can be found here: mayhewlabs.com/.../mux-shield...
Hi
I am using pca 10040 and nRF5_SDK_15.2.0_9412b96
Is there a way I can modify the LOG feature so it comes out on a UART instead of the USB COM port. This is probably...
I'm trying to connect to the Internet from Android Things connected to an NCP through the OpenThread Border Router.
1 Raspberry PI running RaspPi_OT_Border_Router_Demo_v2...
Hi,
I have the need to wait a few ms, from 1 to 20, in several parts of my code and I was wondering what's the most energy efficient way of doing it. Notice I don't need...
Nordic released nRF52811 to support BLE5.1 direction finding. But how to find external IC that related antennas supporting direction finding? If you have specific external...
