Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Ref https://www.nordicsemi.com/Applications/Audio-and-Music seem can via nrf52 stream audio.
Is nrf52840 possible streaming audio in, out and transfer MIDI data to other...
Hello! I am using the nrf52832 sdk15.2 development project now, I don't need to use the whitelist function, so I use 'init.config.ble_adv_whitelist_enabled = false' to turn...
Hello! I am using the nrf52832 sdk15.2 development project now, I don't need to use the whitelist function, so I use 'init.config.ble_adv_whitelist_enabled = false' to turn...
Hello,
I have some problem on my mesh application. (similar application as simple-onoff model)
Sometimes, the server(sensor) devices fail to transmit packet while receiving...
Hello Nordic Community, this is my first post, although I've been using the forums extensively for development.
I've been working with ESB on the nrf52832. The protocol...
I'm playing around with the light and switch examples with the Bluetooth mesh SDK on nRF52832 devices. I'm trying to find out what the maximum distance would be given changes...
Hello, I'm new to this devices. I have several NRF52840 devices and i want to connect them to a Raspberry PI via BLE. I'm not using sensors yet, I just wanna establish a simple...
Hi,
I use nRF5 SDK v15.0.0. In my application I need to change Bluetooth identity address. I can not use BLE_GAP_ADDR_TYPE_RANDOM_STATIC address type, because I need to...
Hi,
I have migrated my projekt from SDK 14.2 to 15.2, the bootloader is basically the secure_bootloader example with some tiny adjustments. When I try to upgrade my product...
Hi all,
I encountered problems porting MbedOS based software which uses Bluetooth Low Energy from MbedOS 5.10 to 5.11 to use the extended features od BLE 5.0.
The ble...
I have interfaced two Nordic nRF52840 boards with one as master an other as slave .
In the image attached signals from down depicts Salve seelct,SCLk MOSI and MISO of Master...
I run into problem, I think for now resolved, but questions remain: Do I have to stop BLE whenever changing ADC config? What did not work?
I don't know why it does not...
Hi, we made a custom board with nrf52832 and flashed example code experimental_ble_app_blinky from sdk13.
We are trying to change the radio txpower other than 0db (default...
Hi all,
I have a nRF52840 development kit and flashed (I believed it flashed successfully) with direct test mode .hex file from SDK 15.2. What I facing was not able to run...
