Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I have a suggestion for an additional feature to nRF Connect for Desktop:
When doing DFU with a zip package that contains a bootloader + softdevice -combo and an application...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
Hi,
I have a pretty extensive nRF52832, SDK14.2, freertos project built and debugged using Keil MDK.
I'm trying to port this project to SES and experience some problems...
Hi,
LED is on when the button is pressed. Press the button again and the LED off. I want the Turn the LED on as long as I press the button. Turn off the LED when I stop...
Hi there,
I've already implemented a custom firmware for nRF52832 with SDK 15.0.0 and S132 v6.0.0 which uses both advertising and scan operations, and now I'd like to use...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10
I'm wondering why the pairing request sometimes shows up in the notification bar and...
Hi,
I am using nRF52832 with sdk 15, freertos.
I need to implement the following logic:
1. Get into low power mode, while keeping a timer running.
2. Every 10 mins...
I was using NRF52832 and s132 v6.0.
I have Android phone's IRK and I have added the Android phone into the identites list manually.
After doing the direct advertising...
In the NRF52-DK user guide, the following is stated:
Important: When using ANT/ANT+, the 32.768 kHz crystal (X2) is required for correct operation.
However, I could...
I need a help to create a mesh where two nrf52 dk are connectred in the mesh and one node sends a message and another node recives it and sends to a url
Hello,
BLE MESH 3.0 Light Sw Example code just I have add APP_TIMER_MODE_REPEATED and its work fine.
Case 1:if I print string Or LED Toggle Based on timer its working...
Hei there!
First of all thanks for all the great work here!
My question is:
In my application, the final device will have 4 pogo pins.
Two of them are for power, the...
Hello All,
Hello all,
I am working on BT832A in which nRF52810 is used and i used segger studio for programming in windows 7. I am refer nRF52 SDK 15.2.0. And i am load...
In the manual for the nRF5284 there is a listing for some divider settings for the MCKFREQ. The size of the register and the values to set indicates that there are a much...
