Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I have read numerous posts about NRF_ERROR_CONN_COUNT but yet able to solve this solve, my setup is NRF52840 Dongle as central and I want to connect to multiple Heart...
Hello all,
I am currently using the SoftDevice Handler library to enable/disable the SoftDevice and observe requests and state transitions on nrf52832 with SoftDevice S112...
I need maximum throughput in nrf52832. So i enabled DLE and using s132_nrf52_5.0.0_softdevice. The data packet length is 96 bytes in single packet. Conn interval 7.5 and 10ms...
I Can't set nRF5 SKD Root Path to: nRF5SDK=C:/nordic_semi/nRF5_SDK_15.2.0_9412b96/nRF5_SDK_15.2.0_9412b96
I created a global macro as instructed (many times) but the path...
Hi there!
I'm using nrf9160 DK's SiP to establish TLS connection to MQTT broker.
When I call nrf_inbuilt_key_write it returns 13 error code which means "If the operation...
Hi everyone.
In mesh light switch example., i try to add timer0 (or any timer).
After initialize timer, application always jump to timeout event, and i don't know why...
I am developing based on ble_app_uart example of SDK12 for nRF51 DK and I need to switch BLE off completely when power disappears to save battery and switch back on when power...
After reading the document for nRF52840 Radio Peripheral. I have a doubt about LENGTH field in packet format. what is the difference between LENGTH field and STATIC_PACKET_LENGTH...
Everything works fine if i use the default baudrate
NRF_UARTE_BAUDRATE_115200 but if i change it to 250000 or something higher the applications starts and goes directly...
Hello ,
I want to read around 6 analog pins, not necessarily simultaneously. I could afford some delay in between them. i am using nrf52832 dev kit with sdk 15. How do i...
http://developer.nordicsemi.com/nRF_Connect_SDK/doc/0.3.0/nrf/gs_programming.html#building-with-ses
I am following the example at the address below.
However, the following...
Hi,
This error has been bugging me for few days and I still have no luck in troubleshooting it.
Recently, I just changed my work project from nrf51822 device to nrf52832...
Hi DevZone members,
I would like to output the elapsed seconds as a floating point value using NRF_LOG_INFO. However, nothing is generated for the floating point value....
I am interfacing nrf52832 with TI TRF7960A using SDK 14.2.0
According to Application Report ( http://www.ti.com/lit/an/sloa140a/sloa140a.pdf) ,
when receive data, SPI...
