Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
i'm using the nrf52832 with s132 and SDK15. I start the project take into account the example ble_app_hrs_rscs_relay.
The system is composed by 3 different services...
Updating firmware (application) from nrf Toolbox for iOS works fine (hex file), trying to do it from an Android phone does not.
The messages are "Starting DFU ..." then...
Hi guys,
first of all here is my setup: https://devzone.nordicsemi.com/f/nordic-q-a/42768/nrf51-52---sdk15---linux-gcc-st-link-v2
It seems like nearly none of the BLE...
HI ,
I would like to combine the Mesh client role with the Mesh provisioner role. That means, nrf52 application is able to switch between the provisioner and client (privisionee...
Hi to all,
i am developing a project based on PCA10056 dev board and i want use bluetooth and NFC in sametime. separately both of them work fine but when i want use them...
Hello everyone, I am planning to use the nrf52840 with the Fingerprint module (https://www.amazon.in/dp/B07DL2DXJX/ref=cm_sw_r_wa_apa_i_Z.VlCbXSSYVRS ). The sensor interfaces...
I got a new nRF51-DK board. I was planning on using USB to program it.
On the board I see pca10028 sticker. What is this?
Also in the SDK I see pca10028, and other pca...
Im getting this error, but i thing this has to do with some python dependencies, Im getting errors with
pip3 install --user -r zephyr/scripts/requirements.txt and installing...
Hi, I have a defined MACRO which I initialised the values of ble_gap_adv_params_t in main.c. I will pass this to the function to start advertising. I used the example (ble_app_blinky_pca10056_s140...
Currently in memory map nRF5 SDK 15.2 (which apparently is a base for Thread SDK) says for nrf52840:
Bootloader settings
0x000F F000 - 0x0010 0000 (4 kB)
MBR...
The nrfx api includes nrfx_gpiote_in_event_disable/enable , but I haven't found an equivalent of nrf_gpiote_int_is_enabled for a pin. I'm attempting to port an interrupt mutex...
nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ble_app_blinky
nrf_gpio_cfg_output(16); nrf_gpio_pin_set(16);
Set P0.16 to high level under the main part of...
There seems to be little documentation on TASKS_SUSPEND and TASKS_RESUME in the SPIM with Easy DMA section of the nRF52832 data sheet. My assumption is that TASKS_SUSPEND...
Hi All,
I am working on ISP1507 which is based on NRF52832. My IDE is Keil V5.26.2.0. I have had the following problem in the UART example (pca10040e) from SDK 15.0.0. I...
Hi,
I have modified the multilink example to work with NUS and connect to 2 peripherals, but I'm facing issues with data transmission. I suspect really low throughput...
