Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello
We would like to know if we erase/write a page beyond the 10K cycles, is the retention time decreasing ?
Do you have a graph or a table of the retention time showing...
Hi,
Currently，the BLE softdevice used for nRF52840 have released. What about the ANT softdevice?
I want to know the release time about S2xx or S3xx. Can you give me a...
Hi to all,
i am developing a device based on nordic nrf52840 soc and i want use NFC tag type4 peripheral to implement a specific protocol. in normal condition all thing...
Hello,
I got a problem duringing advertising with the following scenario:
I advertise some data to a Scanner.
The Scanner answers with a Scan Request.
The ble event...
I am developing a bootloader that upgrade the bootloader/software/application from SPI flash. I think I can use memcpy from XIP address directly. However, bootloader upgrade...
Hi,
I have downloaded the latest Thingy firmware v2.1.0 and setup the IDE as per [here].( devzone.nordicsemi.com/.../)
The code compiles and upon starting debug with...
Hello everyone!
I have an application that is using FDS to save settings to flash. When fds_init() is called it returns the code FDS_ERR_NO_PAGES. My application does not...
Hello All,
I am looking for help to change the transport layer of the background DFU library. Can we use the serial layer from the regular DFU and if yes please guide me...
1.The last datasheet doesn’t show the GPS work current. Where can we get the data？
2.How long does the chip GPS finish one location action normally？
3.In datasheet chapter...
HELLO
I have trouble connecting dfutarg i am doing this
in doing this tutorial I skipped 5,6,7 in step1
and i coudn't do 5,6,7 in step3 because of not connection
here...
hi,
Does engineering B sample support BLE long range? What is the latest hardware/software to be used? What is the typical range that we can achieve?
Thanks in advance...
Hi all,
So, I have nRF5_SDK_15.0.0_a53641a, PCA10040, Keil. I have built already this project succesfully.
The first NFC touch and further bonding with my HTC phone was...
Hi,
I was running the light-switch example.
I would like to know what particular security used in different step of that provisioning process? I can see in authentication...
Hi everyone,
I am trying to make work a stepper motor by Bluetooth with a nrf51822, Actually it is working, the motor turn, but the thing is I Don't know how to control...
