Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I'm using an application based on the light switch provisioner example (BLE mesh 2.2.0).
I'm wondering if the following is possible:
- Request all provisioned nodes...
Sir/Madam,
I am developing application software using nRF51822 in keil microvision 5 IDE. I want to know how to download the hex file without using KEIL IDE. I found the...
I'm looking for an equivalent simple DFU bootloader over UART similar to the HCI example which was provided in the nRF5 v11.0.0 SDK.
Currently, I'm developing with the Sparkfun...
hi,i have a problem! How to Optimize code space in nRF52810,s112,SDK15.2.0,example ble_app_hids_keyboard.
my method is that disable all the code which run in main function...
Hi all,
Now, I have a troube. In Mesh 3.0, I want to advertising data. This is my function :
#define ADVERTISER_BUFFER_SIZE (128)
And whenever the data changes, I...
I bought a nRF52840 Dongle, to evaluate the use of nRF52840 for ZigBee purposes.
I have been able to flash such firmwares as \examples\peripheral\blinky\hex\blinky_pca10056_mbr...
I have a custom board where both nRF52840 and nRF52832 SOC in it.
i have flashed example Ble_Uart code from sdk15 in nRF52840 but im facing a serious issue.
i can able...
Tôi đang sử dụng bảng nrf24l01 để định vị trong nhà, nhưng tôi gặp vấn đề với định vị TOA và bảng arduino không đo thời gian nhỏ hơn micros, tôi không biết bạn có lời khuyên...
Dear Nordic,
I am trying to setup a custom BLE client service to interact with the Komoot app (Turn by turn navigation).
I can connect to the phone, and receive notifications...
Hello Team,
I am trying to run the example DFU overt TFTP, however I found the description a bit ambiguous. Seeking help to remove my ambiguity.
I am trying to follow...
Hi,
I am unable to program the nRF52 Dongle. What I see is that the "Write" option is not highlighted.
Though the Bootloader and Softdevice are already there on the...
Hi All,
I have downloaded the nRF Mesh SDk 3.0.0 and tried to run. I am trying to run the default nrf5SDKforMeshv300src\examples\light_switch\server for
Here is my software...
I have enabled the whitelist feature based on the ble_hids_keyboard example, but when I load the application it is not advertising anywhere. It is paired with my iPhone, but...
I am having one MDBT42Q device on which I am trying to flash an Example image of Peripheral to check basic functionality by nRFGO Studio.
In my device, I have sorted Pin...
i am trying to run advertising.py from pc-ble-driver-py .
i am keep getting exception from
except IndexError : raise NordicSemiException( 'board not found' ) is there...
