Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
i have a sensor tile STEVAL-STLCS01V1 .the description about this product is in this https://www.st.com/en/evaluation-tools/steval-stlkt01v1.html ..the sensor tile have Bluetooth...
Hi,
I am trying to get the rssi value of the client from servers. I added health client model to server and added app_health_event_cb() funtion from provisioner in server...
Hi -
I'm using an nRF52840-DK with Segger IDE and if necessary, Gcc on a Macbook Pro. I have many years of embedded experience, but an new to the Nordic world. I'm able...
Hi!
I am trying to use the NFC " writable_ndef_msg " code along with the " ble_app_uart " code from SDK 15.0 with Softdevice s140 on nRF52840 DK. I am using keil-MDK 5...
How can I be 100% sure the nRF52832 chip is running properly?, what I do to power up the chip is feed it with a regulated voltage of 3.3V (which really is around 3.17V), on...
We use Nrf_studio to connect our board by uart to enter direct test mode.
But an error occurs in serial connection.
I want to know， use our own project program is allowed...
I have already pressed reset in the dongle, it was pulsing red. And when I write it allways says the same error. I have done this experiment in Ubuntu 16.04 and Windows 10...
Dear all,
I'm struggling writing 32 bytes with FDS in SDK 14.
This is what I do:
Init
(void) fds_register(fds_evt_handler);
fds_init();
while(!is_init) {
sd_app_evt_wait...
Hi, I am using nrf51822 Development kit with 3 buttons, each buttons has different functions. (i) 1st Button is used for the wake the module from sleep mode. (ii) 2nd Button...
Hi I using nrf51DK using keil MDK 5 softdevice s110.
I need to update battery level on every 60s and I have initialize timer and start with this code.
static void battery_level_meas_timeout_handler...
I'm trying to implement extended advertising, using BLE_GAP_PHY_2MBPS to offload 255byte advertisement payload to channel data, defining BLE_GAP_PHY_1MBPS as primary phy ;...
Hi
I am trying to broadcast manufacturer data (beacon example) while changing data from second to second. For that I am trying to use timer2 (as timer 0 is used by SD, right...
Greetings,
For Bluetooth Declarations, will new QDIDs be generated to account for the additional required tests as of January 24, 2019 in TCRL-2018-1.
I'm mainly interested...
Hi,
I need to interface LIS2DH through SPI. I tried many SPI Master example but I am getting all the values as 0XFF. Even the WHO_AM_I registers value is getting 0xFF
...
