I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I generally upload codes from mbed.org to my PC then send the hex file to nRF51822 by nRF51-DK's pins. But I don't want to use cables to upload hex codes to nRF51822. Are...
Hi community,
When I want to use the example multilink peripheral inside the s120 directory example of the SDK 6.1.0, I'm not able to compile the code.
The device_manager_peripheral...
So, I want to make an application where my NRF52 advertises an URL via the Eddystone beacon.
The URL will link to an webpage, that will connect to my device through the physical...
As here said link1 If we want to use flash in the mesh we should ignore APP_ERROR_CHECK(NRF_ERROR_INVALID_STATE) in ts_sd_event_handler() ,
2.And here link2 tell us...
How do I set up a variable length characteristic which is greater than 20 bytes and use notifications with this characteristic?
For example I have several variable length...
In an nRF51-based application I'm working on, I am using the SPIS peripheral and a generated clock signal to send a large buffer out over serial using DMA. I want to use the...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
hi
in tutoriall service beginer there is
static void advertising_init(void)
{
uint32_t err_code;
ble_advdata_t advdata;
// Build advertising data struct to pass...
wireshark 2.0.3 which is what got installed when I downloaded it is not supported according to the nFsniffer program.
So what, and how do you set this up?
I am using a function to read the die temperature data from nRF51822 as follows:
static uint32_t temperature_data_get(void)
{
int32_t temp;
uint32_t err_code;
...
Hi all,
my Setup :
nrf51822 QFAC Build Code A1,Waveshare Core51822 Board
keil microvision
nrf device family Pack 8.6
without Softdevice erased with openocd...
Was testing DFU Failures scenarios on SDK 10 to make sure that the software elegantly handles when an Image fails to transfer/swap/load/disconnect..etc. I find that when an...
Using adafruit sniffer. Windows 7 32 bit professional, windows 7 64 bit professional.
After installing the FTD drivers I see com5 installed.
when I start the sniffer it...
On my own board based on 51822, I developped an HTS-like application with SD8.0.0.
Now, I would like integrate the DFU bootloader.
I follow the "Running the BLE bootloader...
