Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
How can we retrieve all network devices RSSI/LQI value? Is there option to subscribe value for LQI ? We just want to showcase LQI/RSSI on server so user be aware if device...
Hi,
How can I retrieve the complete list of supported input and output clusters for all endpoints on a Zigbee end device? I'm currently able to access the On/Off cluster...
Hello,
I'm trying to use several USB CDC ACM instances with USB_DEVICE_STACK_NEXT. (nRF Connect SDK 2.8.0)
Is there a way to set the VID?
And is there a way to set different...
hello, when trying to program my 9160 board, I get this: I already tried the recover command but that yielded the same results. thanks in advance -shlomo
Hello. I have a question about setting the VS code development environment.
" ">www.youtube.com/watch I installed the above YouTube link and installed toolchain v2.8.0 and...
Hi,
Is there any low power mode option for nRF91xx devices where it can still retain could connection? Can this be achieved through iDRX mode?
Regards,
Pavan Vo...
These are customized UUIDS declared by me
/* Custom Service Variables */
#define BT_UUID_CUSTOM_SERVICE_VAL BT_UUID_128_ENCODE ( 0x821675c3 , 0x4046 , 0x45f9 , 0xb8df...
Hello,
I am having some problems with sending data packets larger than 20 bytes over BLE.
We are currently updating our product, that includes the nRF52832 on a custom...
I have an nRF7002dk & its datasheet mentions that there is a 64 Mb external flash memory. The memory is connected through a regular highspeed Serial Peripheral Interface ...
Hi! I'm using the nRF9160 DK where I am aiming to send over bluetooth device count that was picked up from the nRF52840 on board to the nrf9160 on board via UART. However...
Hello,
We are facing an issue where the sum of count in BLE_GATTS_EVT_HVN_TX_COMPLETE events (member of the ble_gatts_evt_hvn_tx_complete_t structure) doesn't match with...
Hi all:
when I develop with nrf54l15dk and nrf connect sdk v2.8.0 on macOS.during flash my dk board, it show me the info as below:
But, I tried flash my board with terminal...
HW PROBLEM 1 First of all, it seems that the board has some HW issues: when I plug in the USB in the IMCU USB to use the on-board J-Link, the chance of the board booting up...
Hello,
I have failed to get the I2C working on the nrf54l15dk, i have now connected it to a oscilloscope with pull ups.
i have confirmered the pull ups work, but as i...
I made a custom PCB with the NRF52840-CKAA and the same 8MB flash memory chip as the PCA10056 NRF528040DK
I used the MX25R6435FZAIL0 because the MX25R6435FZNIL0 was not...
