Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hei,
I need to find the documentation for the NRF SDK 1.8, there's a page which has links to all the documentation versions:
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
I am working with nRF52840 SoC (custom board) and AT25QL641 QSPI Flash chip. I am on v2.1.0 of nRF Connect SDK. The slot1 (update slot) is on an external flash.
...
I am using the serial port of SDK7.1 to send and receive data, and this serial port is a serial port of nRF51_SDK_7.1.0\examples\peripheral\uart\pca10028\arm. Can this serial...
Hi,
I have a project using Zigbee and NRF5340.
I'm facing a "zboss_osif ZBOSS fatal error occurred" from ZBOSS lib after few days of operation.
I'm wondering if the...
Hello,
first I would like to "set the scene".
* hardware : cutsom board
* mcu : nrf52832
* nRF5_SDK : nRF5_SDK_17.0.2_d674dde
* software : mbr + bootloader + softdevice...
Dear Sir/ Madam,
What is the difference between:
> nRF2401P and
>nRF2401P-R ?
Also, code that is written using nRF2401P - would it still work when using nRF2401P...
I am trying to a interrupt on when the sensor has noticed 1G movement for 150MS
Is this the correct way to configure it?
const struct device * const sensor = DEVICE_DT_GET_ANY...
I want to create a NR3540 DK application that accepts a Classic BLE audio connection, from say, a mobile phone with classic BLE (HFS profile?), and then broadcasts that audio...
Hi, I'm working on a project using Zephyr with LittleFS mounted on a QSPI flash device. However, I'm encountering an issue when trying to erase the flash area. Here are the...
Hello everyone,
I am having trouble using the bt_nus_shell.py script and a NRF52840 development board to send shell commands. I am trying to follow the instructions mentioned...
I'm trying to reflash the dongle with the "connectivity firmware". I previously used nRF Connect to do that, but with the latest version, the bootloader got somehow corrupted...
Hello everyone,
I'm currently transitioning a project from traditional BLE communication to the Nordic UART Service (NUS). The previous setup worked fine, but after replacing...
I get error about MPU error stack size while trying to run the example from ncs v2.7.0 on nrf52833dk
I was able to build correctly and I see in the log file that it gets...
nRF Connect SDK 2.3.0 on nRF52840DK
I am trying to add a fifo to my application but when trying to allocate the memory for the data item, k_malloc always returns NULL no...
