Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi,
I'm working on a very high density board with the nRF54L15-QFAA (we want to prevent using a CSP) and I'm running into some routing issues. While looking for optimizations...
Hello, We faced with issue in which we are not able to get the time from the network and because we don't have time, we can't use JWT. As I understood issue is because of...
Hello everyone, I am want to write custom radio protocol for the nrf5340. I have already tried the ESB protocol. But that is somehow limited on the latency (I will open a...
I'd like to use the nRF52832 for cost reasons & I know there are different Bluetooth audio standards, which the nRF52832 does nto support the latest. I don't need hi quality...
Hi, I have a question about the WDT documentation in nRF5340 Product Specification v1.6.
Question 1:
The chapter "Reload Criteria" (7.41.1) is maybe a bit ambiguous defining...
Hello,
I am using the LTE IoT 4 Click board based on the nRF9160, with SDK version 2.6.0 and modem firmware version 1.3.6. I read in the documentation that the nRF9160 provides...
We are developing digital stethoscope and would like to use nrf5340-audio DK as starting point. We need to first get the microphone out on the headphones jack in the DK and...
Hi everyone,
I am using SDK Toolchain v2.3.0 and my code is based on the aws_iot example. I am getting either "cJSON Parse failure" or "Failed to print JSON object" error...
Hello, I am using nRF Connect SDK v2.9.0. While working on the nRF52840 board, I used sys_poweroff() to put the board in deep sleep mode. But before calling it, I called ...
I'm still somewhat new to this but have working code using build 2.6.1 and toolchain 2.6.2 and want to create a sysbuild branch to try with 2.9. The toolchain version used...
Dear Nordic Team, I would like to consult you about that, is there any way to flash modem shell to the custom PCB which already has nRF Cloud connection for location application...
Hi,
1.
I've been trying to get the lte_ble_gateway / let_sensor_gateway example wroking on the nrf9160dk v1.1.3. The example keeps failing at the No HCI driver msg. I...
Hi,
1. Check whether the nRF7000 supports setting the Radio test sample to Non-signaling mode TX test setup for packet generation
https://docs.nordicsemi.com/bundle/nan_046...
HI guys, I'm trying to figure out whether the problem I'm having is a hardware or software issue.
So, my problem is: I have created a custom board using the nrf5340 and...
We are facing strange issue we have this board https://www.raytac.com/product/ins.php?index_id=47
whenever we flash any firmware it works fine but if we erase from vs code...
