Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
I and looking at using an nRF52 device with the nRF Connect SDK version 2.x with a Zephyr Bluetooth LE Controller in a peripheral application where the advertisement data...
Hello,
I am running windows 10 and started the DevAcademy lesson 1, exercise 1 and exercise 2.
Up to exercise 2 item 4 (add a build configuration) everything went fine...
Hello i am using an nrf52840 s140 and i am trying to write a specific event when takes place to the usb port. I am using the usbd_uart example.
It works fine for the first...
I used Nrf9160 to develop a product. Until yesterday, I had been able to connect to the nb network normally. But today, I found that my device could no longer register to...
Hi, I'm looking for help installing the nRF Connect for Desktop 3.12.0.
I've managed to unpack the application EXE and have picked out all the required pre-reqs to do the...
Hi,
I have a problem, When I first initialize Bluetooth and then initialize FDS for writing, it will fail. However, if I first initialize FDS and write data ,it is OK, then...
Hi,
We develop a custom gateway in which we use iMx6ULL and NRF52840. Both are connected over full UART.
We use this NRF52840 as a BLE HCI controller by flashing the HCI_UART...
I'm following the Nrf Connect SDK tutorials on YouTube and I am at step 3 ( nRF Connect for VS Code, 3: Building an application & Exploring windows ). When creating the build...
I have developed an image based on the AWS IoT example which runs on a custom board. The custom overlay exposes some additional UARTs, LEDs, buttons, etc. in custom pin locations...
hi support team,
customer is asking how to add keep alive time in https request header,
i was trying to do this command as below: adding " Keep-Alive: 60\r\n" in XHTTPCREQ...
Hi there!
I've been digging through the code base but could not find a compile option to enable LOG_DBG() type output so that I can observe the JSON formatted packets sent...
Hi,
1. Please solve the problem of high network current registered to nRF9160 (test environment: no network signal)
2. Rf signal: the test current is normal. See Appendix...
Hello,
I implement my own DFU master in nrf52 using SDK11 to replace use of Nordic mobile App. Target to upgrade is also nrf52 but with SDK15.
I have difficulty to get...
Hi,
How do I set the SPIM3 parameter so that MOSI is low after SPIM3 has sent a byte 0x01?
The test environment
DK PCA10056
SDK :sdk17.1
example :spim3
Thank...
