Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hello,
I'm tryng to update nRF9160sip (rev b1), I push sw4 on power on and I see "MCUBOOT" device on "Programmer v3.03"
Then I select file "mfw_nrf9160_1.3.2.zip" and...
Hi,
I have made my own customboard with the nrf52811. For development I have used nrf52840dk.
I´m trying to program following:
I did solder one PCB by hand. It didn...
Hi Team,
I am looking for a new readily available to test on my Nordic board 52X version.
could you please share the inputs and the source code that i can test and upload...
Hello, is there a guide on what should be done to make the sample codes for the nrf52840_dk compatible with the nrf52840_dongle? If there isnt, can I please know how one can...
Hi,
we would like to set the USBD_SERIAL according to the device serial, which will be an abbreviated version of the MAC address. I've checked the code and can only find...
Hi,
I am getting a similar error. I have nRF52832 board connected to raspberry pi for flashing and debugging using openocd. As soon as openocd command is executed I start...
Hi guys. When reading the OOB pairing example,
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/peripheral_nfc_pairing/README.html
" This...
Hope someone can bring some clarification to me.
I am studying the principle of Shock-burst and a part of that study is to go through every step in the examples of “esb_low_power_ptx_pca10056...
In My Window 10 PC., No connected devices are shown in VS Code when nRF52840 dongle is inserted in PC USB Port.
But in Programmer, nRF52840 dongle can be found.
Device...
Hardware:
Raspberry Pi Zero W
nRF52840 DK running Serial Example and connected to RPi via USB
Custom nRF52840 board acting as a Vendor Model Server
Software: ...
I'm trying to program an nRF52 on a custom PCB using the nRF52-DK and am getting an error when connecting with nRF Connect v3.6.1.
I made the following connections from...
When I add example timer to example ble_app_uart an error occurs.
I followed the template and pasted the code.
Here is my sdk_config.h
An error occurs when...
Hi,
I am programming the nRF52833 DK using the nRF Connect SDK (v2.00). I have built and flashed the Bluetooth: Peripheral HT sample from Zephyr to both boards successfully...
Hi all
I'm using the nRF52832 and I've configured P0.21 as RESET pin.
When I reset the nRF52 via P0.21 while the debugger is running, the nRF52 actually resets but it...
I am trying to implement the ble_app_hrs example from nRF5_SDK_17.1.0 and my board is nRF52840 Dongle.
After program the board, the board can advertise and I can find the...
