I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello,
My company is evaluating the Thingy:91, we're interested in Multicell location lookups. My question is regarding the SDK, specifically if it's possible to configure...
Hi, I am unable to download my program and there's no detailed error messages, if any at all. Can someone please tell me what's going on?
Load "C:\\projects\...\\nrf52832_xxaa...
My company is creating a custom board using the 9160 and 52840. I have a BLE app running on a nrF52840 board that I want to port to the 52840 on the 9160 custom board. And...
I'm a newbie (few weeks) with nRF9160-DK and using nRF Connect SDK v1.7.1 / VS Code on a Windows 10 PC
Good afternoon,
I'm struggling with how to set up and start the...
Setup:
- nRF52832 , Softdevice s132, gcc
- iPhone is the peripheral. A custom service is implemented **on** the iPhone.
On the nRF:
- `#define NRF_SDH_BLE_VS_UUID_COUNT...
Hello.
We are developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
I am creating a function to connect to a central device, have the characteristic set...
Hi,
I am flashing Blinky led hex file on the flash at 0x5E000 location.
And again if i try to flash the different Blinky hex file at the same location. it wasn't working...
Hello,
I could use some guidance on where to look for a power draw that I am not understanding. I am not a hardware engineer but have been tasked with completing firmware...
We experienced an issue in production, in which about 40% of boards had excess current consumption by about 75uA. Root cause was found to be the PIN_CNF of a GPIO pin. During...
Is there any way that a BLE event handler installed with NRF_SDH_BLE_OBSERVER, can stop the execution of other (following) observers?
I have various modules using their...
Hi
I am a student and this is my first project working on BLE. Please keep that in mind.
The end goal is to create a fingerprinting system with a Thingy (nRF6936) as...
I have modified the BLE app Blinky example so that the LED is enabled (state 1) on power up. However, this is not being reflected on the BLE side because when I connect with...
Hi, when debugging, I'm encountering this problem where relevant SPI registers (likely status registers) signaled a successful read before the actual data could be pulled...
