I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi all !
I'm writing this message because I'm having problems trying to increase the number of devices in PAwR (I use Coded PHY).
I based my development on the SDK 2.8...
hello . i tested the sample for the persistance key it worked with the AES key . But when i tried with the EDDSA key i received that error psa_generate_key failed! (Error...
I have 7 GB large .ppk2 file exported by Power Profiler v4.2.1. I am looking for a glitch in power consumption. Doing this manually by scrolling through the waveform in Power...
HI! I am trying to decrease the memory use of my application that is built for a nrf9160 and noticed that tfm creates a 256kB partition that it only uses around 99kB of. RIght...
nRF54L15 has RRAM with error correction codes (ECC) built in, with autocorrection.
I guess ECC errors could either happen due to a power loss during a write (when reading...
i am working with the nrf7002+nrf5340 ns when i run the excercise solution and press the button a couple of times, i get this error *** Booting nRF Connect SDK v3.5.99-ncs1...
I am bringing up a brand new laptop for devlopment.
I downloaded and installesd nRF Connect, SDK 2.6.0, SDK 2.7.0 and SDK 2.8.0. The SDK 2.9.0 installation failed.
I...
I plan to use an ESB as a low latency and high speed protocol.
However, there must be multiple hosts on one network.
Hosts or devices must be able to communicate with...
Hi,
I have a design which mostly follows the reference designs.
I've added a Resistor Network R16/17/24 to allow a UFL connector to connect to the ANT and isolate...
Hello, I really need some help to connect a central nRF52 DK board to a peripheral that was provided to me. This peripheral can connect to a smartphone using nRF Connect and...
NCS 2.7 with Toolchain 2.7
Launch build from Visual Studio
Sysbuild with mcuboot and custom application, custom board
Although the application itself updates when VERSION...
In our custom board nrf5340-nrf7002, tried system_off(C:\ncs\v2.6.1\zephyr\samples\board\nrf )sample to check power consumption.
But it measures 0.60mA Is there any config...
Hi Nordic DevZone team,
We would like to get nPM Power up for nPM2100 because it seems not to be supported for nPM2100 in nRF Connect.
We are plannning to let the customer...
I've worked with the nRF5 SDK in the past, and I've started exploring the nRF Connect SDK for future projects. I've taken some of the courses offered through Nordic (great...
I've just launched VSCode for an old project from the nrfConnect SDK launcher, and it seems like the plugin no longer works correctly. It does not search for custom boards...
