Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I am looking for example/ sample implementation of secure boot/ erase using NCS SDK v1.6.x, suitable for nRF52833.
Please point me where I can see such code, or document...
Hi,
I'm trying to integrate buttonless dfu to our project. We don't have any security concerns and given the existing project constraints, it's not desirable to use peer_manager...
Hello,
I tried the smp_svr example with the nRF52-DK of sdk 1.6.1., i compile the solution whit segger v5.50c
I connect with the NRFConnect Device Manager app,
I try...
Hi all,
I am trying to get started with the Nordic thingy 91 but I am not able to update the latest firmware.
The programmer is only showing one Serial port. The instructions...
Hi Nordic Team,
I have interfaced bme280 with nrf52840 and I got the temperature successfully. I have used https://github.com/knuta/nrf5-bme280-twi link for that.
Here...
hi.
I use nrf52840 sdk nRF5_SDK_17.0.2_d674dde.
I need to control the H and L changes of IO within 300ns, I want to turn on the high-frequency part when necessary, and...
Hi nRF team,
we are building our project on top ble_template_example, and we want data encryption for bluetooth data .
we have seen below ways :-
1.) AES Encryption...
I had a generic USB dongle that I used to receive beacons on my machine from an nRF52832 chip.
To be able to perform OTA DFU, I replaced that generic USB dongle with an...
Dear NORDIC Engineers
I have a qustions about NRF52.We have a project that used NRF52833.We want to add the AOA&AOD function to the project.So I would like to know about...
Building the pc-ble-driver on an Arch Linux machine fails with the following error
./pc-ble-driver/src/pc-ble-driver-4.1.4/src/common/transport/uart_transport.cpp: In member...
Hi,
I'm considering using NRF52832/52840 as BLE central while configuring its I2C as slave.
Should I initialize I2C with TWIS instance? How do I suppose to set the slave...
Hello,
I am using the SMS sample of the NRF9160 SDK version 1.6.1. It allows to automatically send a SMS to a precise phone number, and to receive SMS.
As indicated at...
Hi,
I have been trying to use CMSIS DSP library over nRF52840. I added appropriate CONFIGs in prj.conf file, and cmake file. However, whenever I try to use function from...
Hi,
I would like to change the CDC_ACM UART (CDC_ACM_0) baud rate in runtime mode on nRF5340, but it seems to be not working. Below is my code snippet:
The return value...
