Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello to all,
(If "TLDR" go to "### TLDR ###" in the bottom of the page, where you'll find the straight questions without all the context... ) Me and my team are using the...
Hi,
I noticed that the value raw_uuid_len in function ble_advdata_uuid_find() in module ble_advdata.c is fixed at the value UUID128_SIZE.
So the function can only find...
Hi, I am new to NRF and segger embedded studio.
So I want to send temperature sensor data connected with nrf52840 DK to the Murata1_SC device using UART.
The data will...
Found a potential "weirdness" with the mergehex utilty. When merging hex files containing code, dont seem to have an issue. Recently I was using mergehex create a full programming...
Hello Team,
Can you please confirm if we can use the crypto API to do AES encryption/decryption. Can I use it in non secure app and in application and not in bootloader...
Hi,
We want to make some BLE application for nRF52840 on Thingy:91. Referring to PCA20035 schematic, there are some spare pins which we assume is available for GPIO as...
Hi, we have a product (NRF51 SD8 S110 RBCMesh) on the market that craches about once per year the line that asserts is line 189 in src\\soc_radio_timeslot.c (your code) and...
Thanks in advanced. Platform is: nrf52832-qfaa, SDK_17.0.2, use V6.88a JFflash. I design custom board with cp2102n and nrf52832 to act as a usb receiver. All these boards...
Hi, I have flashed the nRF52840 dongle on macos (11.4) and ubuntu (20.04.20) using nRF Connect for Desktop (3.61) following the guide ( https://infocenter.nordicsemi.com/index...
Hi, I'm trying to run my app on a custom board, I keep getting the error "stopped by vector catch" before any of my code runs. I've tried sample programs for the equivalent...
Hello,
I am using one nrf52840 based SOC with nRF5_SDK_17.0.2_d674dde SDK for one of our project. I am trying to utilize internal 1MB of flash for storing some data. For...
Hello everyone,
I am working on a project using FDS. I am using the nRF52832 with the s132 SoftDevice.
As far as I can tell, the code I've written to store data records...
We are building a consumer electronic device which uses: HW Version : nRF52833 on our PCB.
We need mesh to be implemented as we large number of devices connected a single...
Hello,
I am using a central with SDK 14 & nRF52832; my goal is to read the RSSI & MAC from a connected peripheral device. During the BLE_GAP_EVT_RSSI_CHANGED event what...
