Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I'm using arm-none-eabi-gcc (10-2020-q4-major or 9-2020-q2-update) to build my firmware. For some reason recently it started to overflow the flash, and I can't figure out...
I inadvertently flashed my PPKII while trying to flash a 52840 Dongle. Now my computer doesn't recognize the PPKII when I plug it into the USB (PPK does not light up). I've...
Just need a little help on something that is probably very simple. I am sure I will be embarrassed at how simple this is.
I get the nr52 device MAC address and append 4...
Hello All,
I have a requirement where temperature Sensor is collecting temperature data constantly. If temperature data is changed by at least 10% from previous value...
Hi Nordic,
I am been using nrf connect sdk 1.5.1 for several days. As far as I can see, there is an example, named nrf desktop in the applications examples.
May I ask...
Hi,
I am trying to interface a BME680 sensor with my nRF5340 DK. I am trying to get the following sample to run (I left everything default): https://developer.nordicsemi...
Hi,
I'm working with the CCS811 sensor example from the `v1.5.1/zephyr/samples/sensor` folder and I managed to compile it successfully after modifying the files in the ...
I am moving my project up to SDK15.2 from SDK14.2 and all is good except when I try to connect a ESP32 device.
When connecting to the 14.2 code, I get this in the debug...
Hi Nordic,
I have successfully Implemented a single bank DFU [button less dfu] with my customize service
but I don't know how to enable a dual bank DFU in my services...
Hi! I'm using NRF52832 with SDK 15 and the application is running as expected. To optimize power consumption I'm using a conditional statement to put the chip in sleep mode...
Hi,
I am trying to improve the nrf QSPI driver on Zephyr to handle anomaly 122 on nrf52840. Our application needs access to external flash as also as other modules that...
I'm debugging radio test sample and I'm having some problems. The first step is to compile NRF / samples / peripheral / radio with SES_ Zephyr.hex in test project. Second...
Hello,
I found this great blog entry about synchronizing timers on different devices: https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts...
Hello, I am using nRF52840, SDK v16.0, mesh SDK 4.2.0 and softdevice S140 7.0.1. I am following this example to experiment PA/LNA features, namely controlling the pins that...
I have a board with the MBN52832 from murata, that i can program with a Jlink with ease, but wont do adv.
I do believe the problem lies with some config that im not doing...
