Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
we are currently using NRF_LOG_INFO over UART. We print out some values from time to time (seldom). Assume we never go manually to some of the sleep modes.
We use...
With SDK for Mesh v5.0.0 the STRATEGY_ON_POWER_DOWN doesn't work correctly over multiple power downs.
If an entry is set and the stack is powered down, the entry is written...
Hello!!
I am using Radio Transmitter/Receiver example from nRF5_SDK_17.0.2. I am able transmit and receive data on NRF52832. Is it possible to receive the data apart from...
Hi,
I have a huge issue with NRF52832 and DFU on custom board. I have a custom characteristic in my application to switch to DFU after proper PIN typing. Then I call this...
Hi All,
I'm trying send custom board(nrf52832) sensor data to DK by ble uart and multilink.
When I build the code in Keil. I got the message:
..\..\..\main.c(544): error...
I am using the light bulb example and connecting to the Zigbee2MQTT. The Z2M is running on a docker with logs level set to debug.
So from the light bulb example, how can...
Hi. So, pretty sure I've got the firmware installed right and plugging the dongle in creates a "/dev/tty.usbmodem1101" entry. Problem is I have a crash in Python:
This...
I am going to send a sequence of notifications and the documentation provides this information
The API functions that may consume an application packet depending on the...
Hello,
I am using the nRF52811 for my project. I am in the layout design phase...almost completed and I need some clarifications before I launch the first Proto.
I don...
I have found a lot of people having problems debugging with the SD enabled, but we are not using any BLE atm. We are just using the softdevice for OTA updates. But this is...
hi support team,
i just want to confirm, for mesh SDK, i can only find "APP_UNACK_MSG_REPEAT_COUNT" to increase message repeat count, for ACK message, i can't find any...
Hello NRF Team,
We are using nrf51822 chip for one of our product. Currently, we are using a GPIO connected to user button to Turn On the device from system off sleep mode...
Hi,
I have an issue with broadcasting Eddystone TLM + iBeacon, my project is based ble_app_eddystone example and nRF5_SDK_17.0.0_9d13099, SOC is nRF52832.
Beacon advertise...
Hello,
I am developing a circuit which is based on nRF52820. I got the boards manufactured but they are not functioning properly for some reason.
Following are the errors...
