Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I want to make universal AC remote, using nrf52840.
I have decoded IR codes of all AC remotes which have been decoded using IRremoteESP8266 library.
Since AC IR...
I have migrated sdk 15.3.0 to 17.0.0 to my project.
I changed some sdk_config and Makefile for the migration.
after compiling and flashing my device which is nrf528040...
Hi there,
I recently purchased some nRF52840 Dongles for evaluation.
I installed the nRF Connect SDK v1.4.1 and attempted to build a few of the sample projects using the...
Hii guys ,
I am using custom board bluetooth module based on nrf52 which is CBTMN10. I believe I am able to dump example code on my custom board bluetooth module using...
Hi
Is there a way to avoid entering a second time into bootloader mode, if the NRF_BL_DFU_ENTER_METHOD_BUTTON is still pressed after timeout?
I want to enter into the...
Hi,
I am developing a PC app to Buttonless OTA DFU a device(nrf52840) using BLE USB dongle(nrf52840).
1 . The device need a secure bootloader and the ble_app_buttonless_dfu...
Hi everyone,
I am working on the USB MSC example. I am able to create files and perform read and write operations.
Now what I want is to check if there is a FAT volume...
Hi ,
I'm use TWI scanner in nRF5 SDK v17.0.2 . I want to read the value of BM1383AGLV via TWI.
Now I could read the value in a infinite loop , but it is so fast . So I...
Hi Nordic tech support team,
I am currently testing DFU in my custom board (DWM1001) with secure bootloader and buttonless DFU. I was able to completely test the secure...
Hey,
I have configured 2 Thingy 52s , 2 nrf52840 Dongles and 1 nrf52840 Development Kit in a Mesh using Mesh Android Application
I want to create a Blinky type application...
Hi,
I am trying to do dfu in nrf52832..i made a zip file containing (app+bl and sd).the size of zip packet is 530 kb but the application space in nrf52 is only 328 kb..while...
Hi, I want to add PPP protocol to the Zephyr mqtt_azure example. I am using an nRF52840-DK with a Quectel BG-96 Modem. The generic Zephyr gsm_modem example using PPP is working...
Hi, I am using nrf52840 with S140 Soft device and SDK for Thread v4.1. In our test setup we got around 50 FTD devices in the same network. In some time interval we need to...
We are trying to connect the nrf9160 to a spi flash device. we have a custom board with the following pins connected:
sck: 27
mosi: 28
miso: 30
cs: 29
wp: 31
reset...
I would like to use the CC310's SRP accelerator with an application that uses S140. The uC in question is nRF52840.
I have added this code to the ble_app_blinky example...
