after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi, all,
I am working on nRF52832 using pc-ble-driver-py bindings to interface my BLE peripheral. Now I want to build the BLE communication between one central to multi...
Hi
AFter setting the switch sw5 to nRF91, itried to update the firmware using nRF connect V3.4.2
I got the following Error
Error while probing devices: Error occured...
Hello,
The Power Profiler Kit(PPK) is not able to measure current consumption. I got this notification asking to reprogrammed the device, I clicked yes and then-after it...
Hi All,
I am currently in the process of designing the PAB layout for my design. My schematic follows the reference design 4 recommended by Nordic.
In this VDD_HV (From...
Device: nRF52832
SoftDevice: S132, 7.0.1
SDK: 16.0.0
I want change DEVICE_NAME by nRF Connect APP, then I add below code, but I found it die here "wait_for_flash_ready...
Hi everyone,
I am working on a project where I have to enter the system into System OFF mode and RAM retention. What I actually want is to retain the value of some variables...
I am using the NRF52840 and SDK15.3. My goal is to sign a payload using RSA and then verify on the NRF side of things.
The signing scheme is done with openssl on my computer...
Hello!
Is it possible to supply the Nordic Thingy:52 board from an external supply, different than the battery (for example, through the USB)?
I only see the battery option...
Hi all,
I wanna connect an accelerometer sensor the nRF52840 DK board. I think it should be connected physically at the pins P0.17, P0.19-P0.23. But the thing is, those...
hello Nordic
i want to use the bl652 laird development board (nrf52832) as a debugger for the nrf52840 dongle
i have been working with that board allready so it has...
Hi,
I'm trying to implement Eddystone beacons in my application.
My application is already contains advertisement feature with whitelist.
When I'm trying to use...
Hello,
Does anyone have some recommendations about what crystal to use with nRF52840?
We have been using FA-20H 32.0000MF10Z-AJ0 but now it is not in stock and we need...
Hello,
I have configured MQTT over TLS to connect to our broker. Everything works great except that the modem stops reconnecting to the broker after exactly 22 connect-disconnect...
Hi, I'm trying to run the nfc_pairing example from the master branch (1.3.99) of NCS. I've successfully built the example in SES and loaded it onto my nRF52840DK, but the...
I'm wondering how BLE signals are handled at the layer below the scanning module. Namely, suppose there are hundreds of BLE modules that are all advertising nearby. How does...
