I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hi,
I'm working on a Keyboard&Touchpad project, very similar configuration with Smart Remote 2, so I'm considering to use nRF24LU1+ as receiver's MCU. The receiver will be...
Hello, I am working on bare-metal with the BSDLib on a custom board. When trying to debug a specific case in which our server refuses TLS connection, I wanted to see which...
Dear all; I am an originally signal processing expert working on "positioning in smart cities" for IoT using bluetooth 5.1. As part of our new tasks, we are to evaluate the...
I have several nrf52832 based (similar) devices, all are programmed once (at least), now when i try to update program some of devices cannot be programmed (about 5...10% of...
we make the tracking system. so, we want to measure the voltage of li-po battery (i am using nrf51 sensor tag with li-po battery), so, their is any circuitry or any API or...
Hi!
Program enters infinite loop in `sd_ble_gap_adv_start`.
Setup: I've seen https://devzone.nordicsemi.com/f/nordic-q-a/11818/sd_ble_gap_adv_start-hangs-after-disconnect...
Hello,
I've been trying to get a Thingy:91 to connect to the nRF Cloud from Shenzhen, China.
The modem is updated to mfwnrf9160120 and the firmware is on thingy91_nbiot_dfu_2020...
Hello,
I Have a custom PCB with Fanstel BT832 module soldered. Because that module does not have a 32 KHz quartz I need to set use the internal RC source instead. The problem...
Hello,
I am trying to understand if I am able to use the SPI pins as GPIO when SPI is not being used. This post says that we could be able to use I2C and SPI pins besides...
Hi
My English is not very good, but I encountered a problem that could not be solved. Please forgive me if there is any improper expression in grammar.
am use SPIM . I...
I have an issue in buttonless dfu,I have 2 kinds of device,one has issue in dfu,another one has buttonless dfu and works well, I transported DFU code form another kind of...
Hi.
Development platform : nRF52833-DK, s113, SDK 16.0.0, IAR 8.31.1
I am in the process of RF certification.
I downloaded the example at "nRF5_SDK_16.0.0_98a08e2...
I tried in vain to connect my nRF51822 eval board with LIS3DH using SPI. Currently I am using the SPI example in PCA10001 with spi_master_init and spi_master_tx_rx function...
Is there an issue with my clock that's causing the BLE not to advertise? The debugger seems to an error on the gatt_params_init() function, which should mean its a RAM address...
Dear BLE mesh Experts, We want to provision and operate a mesh network using an app that is running on various phones. The idea is to use a single phone during installation...
hi Forum. I'm working on a project with nrf52840 + S140 + TWI (SDK v16). Got all working separatly on my custom board, i.e. softdevice alone works fine and TWI also works...
