Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi there,
I was wondering how the motion pane is supposed to work in the bifravst app, it doesn't seem to be refreshing. The battery pane doesn't seem to be refreshing either...
Hello.
I'm reading the documentation of the radio peripheral of nRF52832 but I can't find any information about the S0 and S1 fields.
What are those fields? What do they...
Hi, guys. I'm using the PCA10056 and the SDK 15.3's BLE UART peripheral example. I'm working on a PWM controller using the mobile app.
I need to create a delayed PWM signal...
My current project is to build a simple BLE LED controller. The goals of this project are to familiarize myself with lower level modules and to practice designing/building...
Hello,
I'm trying to create a project from scratch and write my own drivers. I have strong background in C but unfortunately I don't know anything about assembly. I could...
Very strange, I have lots of nRF52x experience, but this one has me stumped.
Successfully updated our custom board/application from nRF5_SDK_15.0.0 to latest as indicated...
Hi all, I apologise for this very basic question, but I don't understand how to add/enable RTT debugging to my code. I want to practice writing basic code for the NRF5 SDK...
Could you please advise me regarding BLE security?
For security purposes, UUID data shouldn't be included in the advertising data package?
If we don' t put UUID in the...
Hello
My custom board has only 1 button and I'm trying to detect 3 button clicks. The first click is waking up the device and the other 2 are configured as BSP_EVENT_KEY_0...
I have a setup similar to this
When the callback is executed, the execution will enter the inbuilt_key function and then the output will stop and the execution will halt...
I'm using v1.2.0 for the nrf project and I am fairly confident I am using modem firmware 1.1.1 (though I don't know how to verify that).
I'm basing my project on "cloud_client...
Hi,
I am evaluating the ble_app_hrs_pca10056_s140 project with nRF5SDK160098a08e2 Dev kit and nRF82540 dev board.
I have put a breakpoint in line:
*p_erase_bonds = ...
Goodmorning,
what is the maxium current output for SPI pins on the nRF24LU1? The datasheet say "IVDD External load current" of 2mA, is this refered to the internal regulator...
In the documentation of the nRF SDK for Mesh v4.1.0 is written: "The following figure demonstrates how the data packets flow between mesh nodes and their layers within the...
Hello
Beacon using timeslot API
I am trying to implementing a beacon functionality using your timeslot API.
The beacon shall run in parallel to the normal SoftDevice...
