I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello,
I am trying to figure out a way to configure the adc node using the .dts Device Tree file in a similar way to what is done for other nodes such as &spi and &i2c....
I've installed the nRF Connect SDK Master manually since I need the Zephyr modules for a school project. I've manually installed the SDK before without issues but on my new...
Hi Dev team,
I am working with a nRF9160DK board. I am currently getting an error while building my SPM folder in : C:\Users\adeel\ncs\v1.3.0\nrf\samples\nrf9160\spm.
...
Hello!
I'am from austria and try to connect a Thingy:91 to your nrf-Cloud. First I tried it with your
iBASIS sim-card, but in austria we can't use this card.
Then I...
Hi all.
I did a layout with NFC antenna with a nRF52832 chip.
In the schematic (suggesten on datasheet) I have antenna coil with 2 capacitors to ground.
Drawing...
Hello everyone.
I would like to set-up a mesh network of Thingy:52 devices and an nRF52840, which would help me communicate from the an external stimulus to the phone, via...
I have an application where the nrf52840 dongle is hooked to a sensor. The sensor drives a pin high, the mcu grabs data from the FIFO (SPI) and puts it in a buffer. So far...
Hi Team,
We need to use Flash as EEPROM and we have the following queries,
1. How much maximum size of Flash can be configured/emulated as EEPROM/NVM?
2. Whether below...
When using the serial_lte_modem application on a custom nrf9160 board I have discovered that I get nothing out of the UART unless I pull VEN low and then release it (reset...
Hi guys,
I am using Zephyr RTOS and trying to enable my device to send the voltage data via BLE. I use two nRF52832 boards, one of them is peripheral for which I use peripheral_ht...
Hi Team,
We need to know the what kind of security level available in Nordic nRF52X(nRF52833).
Secure boot support and where the 128bit AES keys are stored and accessed...
Hi Team,
We are going to use nRF52833 chip-set and we need the below information based on this input we will decide our chip-set.Kindly update your support.
1. What is...
Hi ,
The size of the boot loader partition 24KB is fixed for the lifetime of the device or it can be extended, as we have some feature to add like firmware update.
Firmware...
