Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
For the testing purpose, I would like to send a few basic packets from LTE Link Monitor on nRF9160 DK to our cloud. I found a way how to do it through the nRF9160: Serial...
Hello guys,
We are developing our IoT prototype with Thingy:91 board using v1.2.0 tag.
One of the things we need to to is as follows:
Scan the BLE area looking for...
Dear Nordic
In ble_advdata.c of nRF5_SDK_16.0.0_98a08e2 , with the function:
I think parsed_name_len < strlen(p_target_name) should be parsed_name_len <= strlen(p_target_name...
After the update from the SD4.0.2 to the SD6.1.1 (nrf52832), it is not anymore possible to pair with the OnePlus5 (Android 9.0) With the Galaxy Note8 (Android 9.0) it works...
Hello,
So I assume VDD is from USB or the battery depending on whether USB is there or not. So, when the SAADC outputs ~3.258 V (in low power mode) that's fairly correct...
I need to measure with SAADC two channels in the same time (NRF_SAADC_INPUT_AIN6 and NRF_SAADC_INPUT_AIN4).
Is possible ?
Have you an code example?
Thanks
Marco
Hi,
I used a nRF51 dongle (PCA10031) wit the nRF Connect (v3.3.0) Bluetooth Low Energy application to communicate with a MBN52832 development kit. This works great until...
Hello:
I am looking for the best way to capture the SD and application error/fault(s) so that when the device is restarted, the data can be transmitted to the central...
Hi
I have installed the toolchain according to the getting started assistant, nRF Connect SDK v1.1.0
I try to load the asset tracker application in Segger with CMake_lists...
want to add UART communication to nRF52832 with mesh enable.
I have added,
nrf_drv_uart.c
nrfc_prs.c
nrfc_uart.c
nrfc_uarte.c
files into nRF_Drivers folder...
Hi,
Let's say I have a network with 5 NRF52833-DK and 1 smartphone with the NRFMesh App. How can I achieve to sniff all the ongoing packets in the mesh network on the smartphone...
