Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I have central based on the 840 and a Peripheral on the 833 , I Need to ability to upgrade the peripheral version from the central.
I know that there is no example...
Hi All,
I am trying to use the RNG peripheral through the softdevice (i am using Version 5.0, with 14.2 SDK) with the sd_rand_... functions. I have enable d the RNG in...
i use the hex
sniffer_pca10056_129d2b3.hex
the packet is
nrf_sniffer_for_bluetooth_le_3.0.0_129d2b3.zip
my board is nrf52840- dk
but the wireshark only capture...
Why any SDK example can't be compiled in Keil perfectly without adjustments to NRF52832?
All examples I've downloades and tryed since SDK11 to SDK16 hasn't worked at first...
the execution procedure of my application as following:
bluetooth_init(void) -> start advertising (timeout 10s) -> nrf_sdh_disable_request() -> nrf_pwr_mgmt_run() -> after...
In the nrf52832 esb function, will data be received on different channels?Did I encounter this problem, or did I change the channel without success?How to judge if I change...
Hi,
I'm having some problems with the IoT library and the power driver. When the program call the "ipv6_medium_init" function, it asserts internally. This happens when this...
Hello,
Coming from different background. I am learning about how to turn my nrf52840 practically useful in indoor localization task.
First step I have adopted the example...
Hello,
while looking at the nrf52 overview page ( https://infocenter.nordicsemi.com/index.jsp ) I was a little bit confuse, that the nrf52840 seems to have no USB anymore...
Hi
I made a custom service for sending radar data from a NRF52 DK and I'm trying to access it with my computer using the pc_ble_driver_py.
I tried to modify the heart_rate_collector...
Hi,
I´m trying to change the "BLE_APP_UART_PCA10010" example, main.c file.
I would like to delete following functions, because I don´t need UART in my project:
...
I am trying to upload firmware using the secure bootloader over UART onto nRF52840-DK. I managed to upload the precompiled blinky dfu test image using the uart debug bootloader...
Hi,
I want to reserve a space of two bytes in flash so I can change those externally. I want to read same memory location from the code.
How do I do it?
How to read...
