Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello Nordic, I am a new developer in Korea.
So, I am not good at English yet. Please understand.
The chip I am using now is nRF52832.
The development tool I am suing...
Hello. The project that I'm working requires both central and peripheral role support, working simultaneously. There are times where, while advertising in the peripheral,...
Assigning Pin 0.06 as SPI clock on NRF52840 does not work. Is there any limitation on pins which can or cannot be assigned as clock for SPI. This is important to know because...
I have been playing with the BLE peripheral examples. It seems like most of these examples have LED1 blinking at a rate of once every 2 seconds. I am trying to look for the...
For my application I need to know (within a millisecond or so) when an advertisement has been received. In my testing so far, it looks like there can be significant latency...
Hi
I'm using a NRF52840 as multi central with 8 connections
SDK: 15.0; SD: 6.1 S140
My central connects to a peripheral with a connection interval of 50ms and latency...
Hi All,
i am stuck in SPI2 enable. i am using sdk 14.2 for our design in previous i am using sdk 12.0
i am simply follow these steps in 14.2 and 12.0 to enable spi2. ...
Hi All,
currently i am facing one issue with SPI,
i am using SPI 1 and 2 for sending data in two different spi slave ics. in that i am successfully init spi_1 and it works...
I am developing a ble device with nrf52832, using nRF5_SDK_15.2.0, and the softdevice s132_nrf52_6.1.0. In parallel I am developing a Windows Desktop application (for Windows...
Dear all,
I remembered that nRF52832 can be powered with button cell, for example CR2450, and worked normally more than 1 year in Nordic website. But now I can not find...
Hi guys,
We're currently experiencing a very strange issue when we perform the following process of writing to a characteristic in an nRF52840 running SDK 15.2.0 and SoftDevice...
I Implemented the code for collecting data from 1 ble device through android app but i want to implement the code for collecting data from two ble device simultaneously unfortunatly...
This ticket started as a mail thread so I add it here so no data are missing:
==========================================================================================...
Hi
In https://devzone.nordicsemi.com/f/nordic-q-a/30206/spi-with-ble-in-nrf52832 , you said it cannot use UART 0 and SPI0 or TWI0 together.
Why?
In nRF52832 Datasheet...
hi...
i had merged the two programs , twi sensor and uart in segger 15.2 version . i am using nrf52840 i am getting the error in twi instance 0 . i couldn't find what error...
