Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
I am trying to send data from a phone to the NRF51822. The data is being sent from the phone in 20 byte chunks to a write characteristic. When the event handler for receiving...
I have been working on a C++ library for the BME280 sensor to be used within the Nordic SDK and am so far only focused on using TWIM, Within this library I intend to use TWIM...
when i use the ble_adverting_start(BLE_ADV_MODE_FAST);
and then use the ble _advering_start(BLE_ADV_MODE_IDLE);
then ble_adverting_start(BLE_ADV_MODE_FAST); the return err_code...
OS ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board CPU :(Nordic) nRF52832 / ARMR Cortex?-M4F 32 bit processor 28-pin Land Grid Array / 15GPIOs / SWD Soft Ver:nRF5_SDK_15...
I have implemented Legacy OOB on NFC and when my Android phone attempts to pair with the device, I receive a NRF_ERROR_STORAGE_FULL error in PM_EVT_CONN_SEC_FAILED event durring...
Hi, now I'm developing my projects(bt-audio-advertiser) with SDK 15.2. and Thingy:52.
I want to load PDM data to extended advertising packets. I succeeded to use extended...
Hi, now I'm developing my projects with SDK 15.2. and Thingy:52.
The projects are bt-audio-advertiser and bt-audio-receiver.
I adapted extended advertising to a Thingy...
Hi,
I have a problem making NFC (with a simple text record) work when I enable SoftDevice: I do not receive any NFC event and NFC communication does not work.
I have a...
Hello,
I would like to get the value of a temperature sensor, convert it from A -> D, send it to a server and then get it with a client (mobile application)
I need a sensor...
Is there any way to perform multiple DFU simultaneously using the single nRF51 dongle. I have to perform DFU from a custom application developed on windows PC. As I need to...
Hi ,
I am running example in nrf52840 using segger embedded studio .
And i am trying to define __no_init variant ,
May be sameone know what is the syntax . in IAR __no_init...
Hi all,
I am building a demo for Bluetooth mesh networking with thingy. I had followed the instructions under this link:
https://github.com/NordicPlayground/thingy52-mesh...
Hi,
I am using the twi_sensor example in the board PCA10056 with SDK v15.2.0. I am trying to disable the internal pull-up resistors of SDA and SCL lines to use external...
There appears to be a design flaw in the nrf_sdk_freertos code that produces a race condition. The race condition can result in a delay in processing a SoftDevice event, or...
When setting up Heartbeat Subscription for a node, a single unicast address is specified as the source. Does this mean that a node can only subscribe to heartbeat messages...
