Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I have 2 nRF52840 Dongles. I am trying to use one to transmit 2.4GHz wireless signal and the other to recieve wireless signal and read the connection strength ...
When I call APP_UART_FIFO_INIT(), receive and transmit some data, then call app_uart_close(), I have 3.7µA sleep current. If I don't call the uart init and close function...
Hyvää päivää,
I'm moving from Eclipse to SES which on the face of it seems smoother and cleaner. My problem is figuring out how to setup my projects. If what I want can...
I am integrating app_timer with no softdevice..
Code compiles and runs correctly at the begining but it only executes the timeout_handler function once after the app_timer_start...
I'm using nRF52, nRF52832, PCA10040 with SDK 15.2.0, nRFGo Studio v1.21.2.10. Is it possible to place all 3 of the following separately on the device using the Studio?
...
The nrfutil documentation/application is used to create a .zip file to dfu update. This package may contain a combination of application/bootloader/soft device along with...
I have looked at secure_dfu_test_images\ble\ for nrf52832 and would like to create a blinky_application_s132.zip (corresponding to hrs_application_s132.zip) to do some testing...
Team,
For asset tracking I am using nRF52840 Beacons as tags in asserts and Raspberry Pi B+ for scanning Beacon's MAC, UID, Major, Minor, Tx, and RSSI values.
To calculate...
I want to send data from nRF52840 Dongle to Raspberry Pi B+, Assume nRF52840 Dongle placed in USB drive of Raspberry Pi B+. Please help with coding sample.
The code assumes that check_rollovers_and_update_eid(...) is called every second, and that m_security_slot [slot_no] .timing increases monotonically with 1. If this is not...
Hi
I have tried to run DFU example from SDK 15.0.0_a53641a.
I also use nRF Connect v2.5.0 to update firmware.
I flashed Soft device and secure_bootloader( examples/dfu...
I'm trying to enable the UART module. The function calls follow:
nrf_init -> nrf_drv_uart_init -> nrfx_uart_init
Here we see that nrfx_uart_init() is called with
result...
I suspect I could avoid writing (admittedly, simple) code to map ble service objects to connection handles and vice-versa if I knew how to properly use the BLE Link Context...
Hi, I am merging the Thingy app (Segger with softdevice s132_nrf52_4.0.5) with the UART example (taken from ble_app_uart in SDK 11). I have been fixing some errors before...
Hi All,
I built a custom board that mounts a nrf52840 chip and I followed the schematic N 5 of the datasheet.
I also have 2 evaluation boards nrf52840 EVB "PCA10056",...
